SpectraPure MaxPure MPRO-300 RO System Скачать руководство пользователя страница 14

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

14

Product Water -  Low Production Rate

Cause 

  Corrective 

Action

Plugged pre-filters 

Replace pre-filters

Low water temperature 

Heat feed water or use higher GPD membrane

Low feed pressure 

Use booster pump or use higher GPD membrane

Fouled membrane 

Replace membrane 

Membrane Troubleshooting Guide

The following chart illustrates the procedure for determination of RO membrane 
performance. However, the chart represents only rough guidelines for 
determining performance of RO membrane. Depending on your tap water 
chemistry, the rejection characteristics of the membrane may vary significantly. 

Method of  Calculate %   

 

 

Test Results  

Conclusion

 Testing  

Rejection

TDS/ 

 

Measure feed water and  Is Rejection   

No - Replace Membrane

Conductivity   RO product water TDS/ 

greater than   

Yes - Membrane OK

Tester  Conductivity 

   95% 

?

Alkalinity  

Measure feed water and  Is Rejection   

No - Replace Membrane

Test Kit   

RO product water  

 

greater than   

Yes - Membrane OK

   Alkalinity    90% 

?

Hardness 

*Measure feed water   

Is Rejection   

No - Replace Membrane

Test Kit   

and RO product water  

greater than   

Yes - Membrane OK

   Hardness    90%?

*Caution: This test is not to be used on softened water sources.

Please feel free to contact us here at the factory for 

any technical questions or problems you may have.

Toll-Free 1-800-685-2783

TROUBLESHOOTING GUIDE

Содержание MaxPure MPRO-300 RO System

















Отзывы: