manualshive.com logo in svg

SpectraPure DWS, Инструкция по эксплуатации

Поделиться
Скачать
SpectraPure DWS Скачать руководство пользователя страница 6

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

6

This procedure will assure you of maximum life and reliability of your SpectraPure System.  Failure to perform this 

procedure can permanently damage the membrane and will void the pro-rated Membrane Warranty.

In order to maximize the life of your SpectraPure RO Membrane, you may need to adjust the ratio of the concentrate to 
purified water. If not enough concentrate is allowed to flow past the membrane during operation, the impurities will 
precipitate out on the membrane surface, clogging the RO Membrane. To keep this from happening, the Concentrate to 
Purified Water Ratio must be checked and adjusted in order to compensate for pressure and temperature variations that 
exist in all water supplies. The flow rate of the concentrate must be a minimum of 4X the product flow rate. 4X to 6X is an 
acceptable concentrate flow rate.
Procedure:
 

1.  Locate the Yellow waste line. Direct the waste line into a sink drain or bucket. 

 

2.  Locate the Blue product line. Direct the product line into a sink drain or bucket.

 

 

 

NOTE: For the DWS-PP, locate the yellow and blue line (shown in the Diagram below) and disconnect them    

 

 

 

from pump to proceed with Measuring Waste to Product Water Ratio. 

 

3.  Turn on the Feed Supply Valve and let the system run for 20 min.

 

4.  Collect product water from the blue line into a measuring  cup for one minute. Measure the collected amount  

 

 

 

in milli-liters. Do the same with the waste water.

   

WASTE 

IN 

MILLILITERS______________

DIVIDED BY

   

PRODUCT 

IN 

MILLILITERS______________

             The resultant is the Concentrate to Product Ratio

(Although not needed in this procedure, the daily product  flow rate in Gallons per Day (GPD) can be calculated to be 

equal to the product flow rate times 0.38 ).

 

5.  If ratio is 

less than 4:1

 

6.  Follow instructions on page 7

 

 

 

(MAKE SURE YOU RECONNECT WATER LINES FOR DWS-PP)

 

7.   If ratio is 

greater than 6:1

, flow restrictor requires replacement (Please contact SpectraPure Inc).

PROCEDURE FOR MEASURING WASTE TO PRODUCT WATER RATIO

Содержание DWS



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды