background image

V 2 0 0 - 1 8 - E 3 X B

S n a p - i n   I / O     M o d u l e

  6 / 0 5

About Unitronics 

Unitronics has been producing PLCs, automation software and accessory devices since 1989.  
Unitronics’ OPLC controllers combine full-function PLCs and HMI operating panels into single, compact units.  
These HMI + PLC devices are programmed in a single, user-friendly environment.  Our clients save I/O points, 
wiring, space, and programming time; elements that translate directly into cost-efficiency. 
Unitronics supports a global network of distributors and sales representatives, as well as a U.S. subsidiary. 
For more information regarding Unitronics products, contact your distributor or Unitronics headquarters via 
email: 

[email protected]

 

 

Under no circumstances will Unitronics be liable or responsible for any consequential damage that may arise as a result of 
installation or use of this equipment, and is not responsible for problems resulting from improper or irresponsible use of this 
device.   
No part of this document may be used for any purpose other than for the purposes specifically indicated herein nor may it be 
reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and/or recording, for 
any purpose without written permission from Unitronics.
The information appearing in this document is for general purposes only. Unitronics makes no warranty of any kind with regard 
to the information appearing in this document, including, but not limited to, implied warranties of merchantability and/or fitness 
for a particular use or purpose. Unitronics assumes no responsibility for the results, direct and/or indirect, of any misuse of the 
information appearing in this document nor for any use of the Unitronics products referred to herein in any manner deviating 
from the recommendations made in this document. Unitronics assumes no responsibility for the use of any parts, components, 
or other ancillary appliances including circuitry other than as recommended hereunder or other than that embodied in the 
Unitronics product. 
Unitronics retains all rights to its proprietary assets including, but not limited to its software products which are copyrighted and 
shall remain the property of Unitronics. Copyright protection claimed includes all Forms and matters of copyrightable materials 
and information legally allowed including but not limited to material generated from the software programs which are displayed 
on the screen of the Unitronics products such as styles, templates, icons, screen displays, looks, etc. Duplication and/or any 
unauthorized use thereof are strictly prohibited without prior written permission from Unitronics. 
All brand or product names are used for identification purpose only and may be trademarks or registered trademarks of their 
respective holders. 
Unitronics reserves the right to revise this publication from time to time and to amend its contents and related hardware and 
software at any time.  Technical updates (if any) may be included in subsequent editions (if any). 
Unitronics product sold hereunder can be used with certain products of other manufacturers at the user’s sole responsibility. 

5410-1082-9 

Spectra GmbH & Co. KG
[email protected]

Spectra (Schweiz) AG
[email protected]

Содержание V200-18-E3XB

















Отзывы: