Spear & Jackson SPJPM40B, Руководство по эксплуатации

Страница: 13 / 24

Helpline No. UK/Northern Ireland
0151 6491500
Rep. Ireland
1890 946244
13
Assembly
1. Take the mower and attachment parts out
of the packaging and check that all parts are
present (Fig. 2).
2. Fasten the push handle (Fig. 3a / Item 2) with two
screws (Fig. 3a / Item 9) and two nuts (Fig. 3a / Item
8) each on either side, making sure that the cable
and clip to be installed later on are not in the way.
(Tighten with a 13mm spanner).
3. Unfold the push bar and fix it into place by
tightening the handle clamping knobs as shown in Figure 3b.
4. Insert the grip of the starter cord (Fig. 3c/Item 5)
into the hook provided for that purpose as shown
in Figure 3c.
5. Fasten the cords to the push bar with the
supplied cable clip (Fig. 3d/Item 9).
6. Lift the ejector flap (Fig. 4 / Item 4) with one hand
and hook in the grass bag (Fig. 4/Item 3) as
shown in Figure 4.
6.2 Setting the cutting height
Important. Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
n
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
n
The cutting height is not adjusted at a single
central point – instead, each of the 4 wheels
have to be adjusted separately. Five different
cutting heights are available (25, 35, 45, 55
& 65mm). (As-delivered state: Medium cutting
height (45mm))
Caution: All 4 wheels have to be set to the same
cutting height.
1. Use the height adjusting lever of each wheel
(see Fig. 1 / It. 6 & Fig. 6a. to Fig. 6c. / It. 6) to set the
lawnmower to the required height for all of the 4 wheels.
2. Each lever is sprung into one of five slot positions
on the wheel bracket. Moving the lever towards the
front of the lawnmower increases the blade cutting
height. Moving the lever towards the rear of the
lawnmower lowers the blade cutting height .
3. To adjust the lever position, pull the lever towards
the wheel, out of the slot position and move it towards
the front or the back of the lawnmower. Then release
the lever into the desired slot position. Adjust all 4 levers
to the same position.
7. Operation
Note: For detailed information on the engine
& oil, refer to the enclosed manual from
Briggs & Stratton.
Important. The engine does not come with oil in
it. Therefore, be sure to add oil before starting the
engine. You will also need to fill in petrol, as this is
also not supplied upon delivery.
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 5a/Item 1) which must be pulled back
before the engine can be started. When the
engine control lever is released it must return to its
initial position, at which point the engine
automatically switches off.
Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
Whenever you need to perform any kind of
adjustment and/or repair work on your lawn
mower, wait until the blade has come to a
complete stop.
Note:
1. Engine brake (Fig. 5a/Item 1): Use the lever to
stop the engine. When you release the lever the
engine and the blade stop automatically (Fig.
5b). To mow, hold the lever in the working position.
Before you start to mow, check the start/stop lever
several times to be sure that it is working properly.
Ensure that the tension cable can be smoothly
operated (i.e. is not catching or kinked in any way).
2.
Warning: The blade begins to rotate as soon as
the engine is started.
Important: Before you start the engine, move the
engine brake several times to be sure that the
stop cable is properly working.
Note: The engine is factory set to a speed that is
optimal for cutting and blowing grass into the
basket and is designed to provide many years of
use.
3. Check the oil level.
4. Fill the tank with petrol when it is empty, using a funnel
and measuring vessel. Make sure that the petrol is clean.