Spark Fire Ribbon Скачать руководство пользователя страница 20

Страница: 20 / 48

Gas Supply Line
Once the vent pass-through (or pass-through

’

s) are finished, the gas supply line should be installed. The

supply line should exit the wall that the fireplace will be installed on at the location specified on the instal-

lation template We suggest the installation of a shut-off valve in the supply line between the wall and the

connection to the fireplace. Your professional gas installer or local gas company will determine the specific

requirements for the gas supply line as the requirements may vary in different locations. In every case, the

installation must conform with local codes or, in the absence of local codes, with the

National Fuel Gas

Code, ANSI Z223.1

or the

Canadian Installation Code, CAN/CGA B149.

Installing the Fireplace Mounting Plate on the Wall

1. The fireplace mounting plate is attached to the wall structure using

six

1/4”

2”

long lag bolts and large diameter washers that are

provided with the fireplace. It is important to use the included

hardware as the full weight of the fireplace is supported by the

mounting plate.

2. Drill a

5/32”

diameter pilot hole at each of the mounting hole loca-

tions that you marked using the template. The pilot holes should

be the full depth of the lag bolts. Be sure that there is solid wood

at each mounting location. If not, the wall should be reconstructed

to provide the needed support.

3. Before the mounting plate can be lagged to the wall the two tabbed

sections of the telescoping vent pipe heat shields that you set aside

earlier must be attached to the mounting plate. Each heat shield

half is held in place with three sheet metal screws (provided). The

inner shield half (smaller diameter) is installed from the front of

the mounting plate. Slide the inner heat shield half through the

vent pipe opening in the mounting plate. Align the three tabs with

the pilot holes in the mounting plate (as shown in the adjacent il-

lustration) and install the three screws.

4. The outer vent pipe heat shield half (larger diameter) is installed on

the rear of the mounting plate. Slip the outer shield half over the

inner shield and align and install the three screws. See the adjacent

illustration.

5. The fireplace mounting plate is now ready to be lagged to the wall

structure.

6. With a helper pick up and align the mounting plate over the gas

supply line and line up with the four mounting lag bolt pilot holes.

These holes are in recessed bosses.

7. Using the lag bolts and washers provided with the fireplace, install

the top lag bolts (with washers) first, followed by the lower ones.

Use a

7/16”

socket wrench to tighten the lag bolts.

Note: It may be helpful to put a light coating of dish or hand soap

on the lag bolts to reduce resistance when tightening.

INNER VENT PIPE SHIELD

(Smaller Diameter)

OUTER VENT PIPE SHIELD

(Larger Diameter)

ASSEMBLY & INSTALLATION

Содержание Fire Ribbon

















































Результаты поиска

Содержание Fire Ribbon

Отзывы:

Бренды по названию

Популярные бренды

Spark Fire Ribbon, Руководство по установке и эксплуатации

Результаты поиска

Содержание Fire Ribbon

Отзывы:

Бренды по названию

Популярные бренды