4
5
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
II. INSTALLATION
1
Transmitter Antenna Installation/Removal
1
Antenna Installation
Turn the antenna clockwise to screw it into the transmitter
body. Securely screw it in place, or a malfunction may result
from having a loose antenna connection.
2
Antenna Removal
Turn the antenna counterclockwise to remove it. When
housing the antenna, retract it from the root rib to avoid
bending the antenna rod.
2
Transmitter Battery Installation
Use eight AA batteries for the transmitter.
1
Slide open the BATTeRY DOOR in the direction shown.
2
Insert AA BATTeRIeS with the polarity (+/-) as shown.
3
Replace BATTeRY DOOR.
* When the capacity of the batteries becomes low, the Power
LeD lamp changes from steady to blinking. You need to
replace the batteries, or a malfunction may occur due to
reduced operating range.
A
B
D
C
1
2
3
5
6
7
8
9
4
1
2
1
1
2
1
2
6
5
3
7
4
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
III. BUILT-IN BATTERY CHARGING INSTRUCTIONS
Adult Supervision Required
A rechargeable battery is built into the helicopter body. Be
sure to charge the battery before you use it. The built-in Li-Po
battery, if not handled properly, may explode, cause burns or
catch fire, resulting in a serious accident.
1
Set the power switch of the helicopter to “OFF”, connect
the charger connector to the charging port on the helicop-
ter, then plug the charger into a standard wall outlet.
1
-1 Charging port.
2
LeD lamp on charger will light to show the charger is
operating.
2
-1 LeD lamp
3
When charging is complete, the LeD lamp goes off. Re-
move the charger connector from the charging port on the
helicopter, then unplug the charger from the wall outlet.
* Battery charging time varies with battery level. As a guide,
it takes approximately 1 hour when the battery is near
empty, or 0 minutes if it is half-empty.
Important:
To prevent overcharge of batteries, do not repeak a Li-Po
battery that has peaked. The battery, if not used to fly the
helicopter, does not require charging in the first one or two
hours after a charge.
IV. HOW TO FLY
1
Preparation for Flight
1
Turn on the switch on the transmitter. Then, the LeD lamp
will start blinking.
1
-1 LeD lamp (blinking)
2
Completely extend the transmitter antenna.
3
Turn on the switch on the helicopter body, then the LeD
lamp will start blinking. When the LeD lamp changes to
steady, the helicopter is ready for flight.
3
-1 LeD lamp
4
Move the throttle stick to the top position, then to the
bottom. The transmitter is ready to operate when the LeD
indicator changes from blinking to steady.
4
-1 LeD lamp (not blinking)
5
Stay at least 10–15 ft (4–5 m) away from the helicopter
before flying it.
6
Only operate the helicopter in environments free from
obstructions.
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
1
2
-1
-1
-1
-1
-1
1
1
1
3
3
2
2
2
3
1
1
4
4
1
2
2
-1
4
Note:
Flying an RC helicopter is an exciting and challenging experience, and requires some practice. Be sure to use gentle
controls on the radio so that you can get used to the way the helicopter responds. Take your time, and make sure you fly
in an area with plenty of space. In the beginning, it is important that you focus on making small movements on the control
sticks of the transmitter. As you get more comfortable with the way your helicopter flies, you will be able to use the full range
of controls. If you have never flown an RC helicopter before, we recommend that you have an experienced RC pilot present
during your first few flights.
