SPALDING M887017 Скачать руководство пользователя страница 7

Страница: 7 / 17

HR83005.EPS

211560

Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to release any

air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level

mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off

any excess cement on mounting plate at this time and place washers (24) onto J-bolts.

PLAYING SURFACE

1" (2.54 cm)

SIDE VIEW

DRAINAGE HILL

PLAYING SURFACE

Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill.

IMPORTANT!

Check leveling of mounting plate

several times with carpenter’s level

while concrete is curing.

DO NOT PROCEED UNTIL CONCRETE HAS CURED

A MINIMUM OF 72 HOURS !

ALLOW ADDITIONAL TIME FOR COLD,

WET OR HUMID WEATHER.

STOP!

Содержание M887017


















Результаты поиска

Содержание M887017

Отзывы:

Похожие инструкции для M887017

Бренды по названию

Популярные бренды

SPALDING M887017, Руководство пользователя

Результаты поиска

Содержание M887017

Отзывы:

Похожие инструкции для M887017

Бренды по названию

Популярные бренды