Spacerails LEVEL 6 Скачать руководство пользователя страница 18

Страница: 18 / 20

Page 18

Rail Section 8:

Splitter A

Step1:

Start by attaching Rail J (550 cm) to the inside Rail Clip

of Splitter-A facing the back of the Base. Proceed to Arms

L-6, Q-6, R-7, O-10, and M-6. Pass by the elevator and attach

to Arm F-7, B-6, A-3, C-3, D-7, E-3, F-5, and G-3. See next

illustration to continue.
Proceed from Arm G-3 to Arms F-4, G-2, I-3, H-4, I-2, H-3, and

I-1. finish with Arms J-1, L-2, P-1, O-1, M-1, and K-1 and enter

the right facing rail clip on the bottom Elevator Ring. Repeat

entire step for second rail.

Step1:

Overhead view of cascading loops in step 1

NOTE:

Congratulations on completing Spacerails Level 8! Fine

tune the rails and see how many marbles you can get

going at the same time. If the marbles are coming into the

elevator too quickly it may knock other marbles already

in the tower out. Create a dip or find other ways to slow

marbles to just the right speed at entrance.

Содержание LEVEL 6




















Результаты поиска

Содержание LEVEL 6

Отзывы:

Похожие инструкции для LEVEL 6

Бренды по названию

Популярные бренды

Spacerails LEVEL 6, Руководство пользователя

Результаты поиска

Содержание LEVEL 6

Отзывы:

Похожие инструкции для LEVEL 6

Бренды по названию

Популярные бренды