Spacerails Level 1 Скачать руководство пользователя страница 3

Страница: 3 / 12

Page 3

PREPARE THE COASTER COMPONENTS

Prepare the Loop:

Press one

Rail Clip to both sides of the Loop

Assembly. Attach the Loop Stand

to the bottom of the Loop.

Prepare the Turns:

Press one

Rail Clip to both sides of all six

Corner pieces.

LOOP & TURNS

NOTE:

Corners are identified on the

bottom of each piece.

RAIL SPLITTER

Prepare Rail Splitter:

Attach one Rail

Clip to each of the Rail Splitter posts.

Step 1:

Attach one Arm Holder A and one

Arm Holder B with one Arm Sheath. Insert

one Arm Clip into Arm Holder A.

Step 3:

Turn the Arm Lock

counter-clockwise to secure

the Arm Clip in place.

Step 2:

Insert Arm Lock through

Arm Holder A and Arm Clip.

ARMS

(QTY: 5)

To avoid damaging parts, do not move or adjust the Rail Clip while locked in the arm. To move the Rail Clip, release

Arm Lock by turning clockwise, position Rail Clip as desired, then secure Arm Lock again.

Содержание Level 1













Результаты поиска

Содержание Level 1

Отзывы:

Похожие инструкции для Level 1

Бренды по названию

Популярные бренды

Spacerails Level 1, Инструкция пользователя

Результаты поиска

Содержание Level 1

Отзывы:

Похожие инструкции для Level 1

Бренды по названию

Популярные бренды