Spa Builders SC-CF Скачать руководство пользователя страница 26

Страница: 26 / 68

SC-CF & SC-MP Service Manual

FLO Flow Chart

If FLO error condition occurs (problem with the pressure switch: pump is
on but no water pressure detected), follow Troubleshooting Flow Chart
below to identify the problem:

Make sure circulation pump parameter is set correctly

(depending on your system configuration).

Is pump working

when you try to start

it from keypad?

Refer to "Pump not

Working" section.

Remove

anything

obstructing

filter.

Clear any

air locks

and verify

water valves.

Verify if

pressure switch

cable is properly

connected

to pressure

switch.

There must be adequate water

in spa for normal use.

yes

Is anything limiting

flow of water into pipes?

yes

Replace

Spa Pack.

Adjust or

replace

pressure

switch.

Lower Set Point at 60

F and

turn pump off.

Short two pressure switch

terminals with a jumper cable.

Does FLC error condition persist?

yes

Содержание SC-CF





































































Результаты поиска

Содержание SC-CF

Отзывы:

Похожие инструкции для SC-CF

Бренды по названию

Популярные бренды

Spa Builders SC-CF, Руководство по обслуживанию

Результаты поиска

Содержание SC-CF

Отзывы:

Похожие инструкции для SC-CF

Бренды по названию

Популярные бренды