Spa Builders SC-CF Скачать руководство пользователя страница 12

Страница: 12 / 68

SC-CF & SC-MP Service Manual

Flashing Dots Flow Chart

If 3 flashing dots appear on keypad display, follow Troubleshooting Flow
Chart below to identify the problem:

3 flashing dots appear on the display!

Remove pack cover.

Is board LED on?

flashing dots

& LED flow chart.

yes

Make sure jumper is

set properly for

circulation pump and

reset breaker.

Start Pump 1 (or

circulation pump if installed

by increasing set point).

Replace pressure
switch if problem

persists.

Do you have

continuity on your

voltmeter for

pressure switch?

yes

Short pressure

switch terminals

with a jumper cable.

Replace pressure

switch cable.

Replace pressure

switch cable.

Remove anything

obstructing filter canister

or piping. Clear any air

locks. Verify water valves.

Try to adjust

pressure switch.

Are dots still

flashing on

keypad display?

If problem persists,

replace Spa Pack.

yes

Verify

pressure

switch

connection.

Try

to adjust

pressure

switch.

Disconnect

pressure switch

for 5 seconds

and reconnect it.

Are dots still

flashing on

keypad display?

If problem persists,

replace Spa Pack.

yes

Replace
pressure

switch

if problem

persists.

Содержание SC-CF





































































Результаты поиска

Содержание SC-CF

Отзывы:

Похожие инструкции для SC-CF

Бренды по названию

Популярные бренды

Spa Builders SC-CF, Руководство по обслуживанию

Результаты поиска

Содержание SC-CF

Отзывы:

Похожие инструкции для SC-CF

Бренды по названию

Популярные бренды