background image

SmartPanel Projector Driver Application Note 

Panasonic PT-LB10VU

 

© 2005 SP Controls Inc.  601 Minnesota Suite 115, San Francisco, CA  94107 

[email protected]

 

II. CONTROL WIRING 

3

4

5

8

7

6

2

1

PROJECTOR CONTROL

RS232

IR/SERIAL

RX

GND

CT

S

RT

S

TX

+1

2V

GND

IR

/S

E

R

SE

N

S

E

RS-232 to 

RS-232C

IR Emitter

(i

ncl

u

ded w

ith 

P

anel

)

1/8" Mini

Female

Male Mini-DIN

RX to Pin 5
TX to Pin 3
GND to Pin 4

RS-232 to

SERIAL

IR Emitter to

any IR window

 

This section specifies wiring for the Panasonic projector.  
 

Note

: The Panasonic PT-LB10VU projector serial port is a 

female 8-pin mini-DIN. This document provides instructions 
for terminating the RS-232 control cable directly onto a 
male 8-pin mini-DIN connector. If you wish to terminate the 
control cable on a standard DB9 connector, an adaptor 
cable may be separately ordered from Panasonic 
(Panasonic part no. 

ET-ADSER

). 

 

 

A.  RS-232 should be connected to the port labeled  
      

SERIAL

.  Connection should be as follows: 

 
1.  Wire the Panel to a male Mini-DIN 8-pin connector as 

follows:  

 

Panel RX to 5 
Panel TX to 3 
Panel GND to 4 

 
2.  Connect the Mini-DIN to the Panasonic projector port  
     labeled 

SERIAL

 
  
B.  The IR Emitter should

 

be connected to the one of the  

      Panasonic IR windows as follows: 
 
1.  Wire the Panel to a female 1/8” Mini as shown; wire 

IR/SER

 to 

tip

 and 

GND

 to 

ring.

 Splicing and direct 

wiring to the IR Emitter is not recommended as it 
makes removal of the Panel for service more difficult. 

 
2.    Connect the included IR Emitter to the female mini. 
 
3.    Affix the IR Emitter to one of the IR windows on the   
       projector. 
 
 

Note: 

The emitter glows red when IR is emitted so wiring 

can be verified. 
 
   
 
 

Содержание PT-LB10VU






Отзывы: