background image

Motherboard Description

SY-K7VLM-B

10

1-8

 

MEMORY

1-8.1 Main Memory

The motherboard has two DIMM sockets. SDRAM can be installed in one,

two, or sockets. Using the serial presence detect (SPD) data structure,

programmed into an E²PROM on the DIMM, the BIOS can determine the

SDRAM’s size and speed. Minimum DIMM memory size is 8 MB;

maximum DIMM memory size is 256/512 MB. Memory size and speed

can vary between sockets.

The motherboard supports the following memory features:

 

DRAM interface synchronous with host CPU (66/100/133MHz) or

AGP (66MHz) for most flexible configuration

 

DRAM interface may be faster than CPU by 33 MHz to allow use

of PC100 memory modules

 

DRAM interface may be slower than CPU by 33 MHz to allow use

of older memory modules with newer CPUs

 

Concurrent CPU, AGP, and PCI access

 

Supports SDRAM and VCM SDRAM memory types

 

Different DRAM types may be used in mixed combinations

 

Different DRAM timing for each bank

 

Dynamic Clock Enable (CKE) control for SDRAM power

reduction in high speed system.

 

Mixed 1M/2M/4M/8M/16M/32MxN DRAMs

 

The K7VLM-B supports 2 DIMMs or 6 banks at 133MHz for 1GB

max memory)

 

Flexible row and column addresses

 

64-bit data width only

 

3.3V DRAM interface with 5V-tolerant inputs

 

Programmable I/O drive capability for MA, command, and MD

signals

 

Dual copies of MA signals for improved drive

 

Optional bank-by-bank ECC (single-bit error correction and multi-

bit error detection) or EC(error checking only) for DRAM integrity

Содержание SY-K7VLM-B




























































































Отзывы: