V110713
323DMaster
TTL
USB
7
6
5
4
3
2
1
P3
GND
12V
RX
TE
TX
2
1
Access Controller
About Master Card
Enter the program mode
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input
876112
→
program mode accessed
Exit the program mode
Input
Operation process
M4/M8: Individual pass code
Card or PIN:
Access programming mode
→
12 UUUUU PPPP [e.g. User address: 00001 and pass code: 1234, input 12 00001 1234 ]
Card and PIN:
Access programming mode
→
13 UUUUU PPPP [e.g. User address: 00001 and pass code: 1234, input 13 00001 1234 ]
M6: Public pass word
Card or PIN:
Access programming mode
→
15 PPPP [Input 4-digit pass code, default value: 4321]
Card and PIN:
Access programming mode
→
17 PPPP [Input 4-digit pass code, default value: 1234; PPPP=0000: change into Card Only]
Enable controller
Access programming mode
→
20 DDD [128= Anti-pass-back(0=Disable; 1=Enable)/ 064=Access/Exit(0=Exit; 1=Access).]
Access programming mode
→
20 128 (Please refer to function default value for details.)
[e.g.] Enable Anti-pass-back, and set to Exit door= (128 x 1) + (064 x 0) = 128
Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or to situations need
access and exit monitor.
C. Anti-pass-back(M4/M8)
B. Set up the password
[Only for connect to external K-series reader]
Master Code modification
Access programming mode
→
09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] Set the Master code to be 876112, input
123456
→
09 876112876112
A. Enter/ Exit Program Mode
Adding Tag
Present Master Card
Deleting All Tags
Present Master Card
P.S. Once MASTER CARD is presented after one
warning beep, all card data will be cleared.
After 3 short beeps
[Access programming mode]
After 3 short beeps
[Access programming mode]
Present one new card at a time
1 long warning beep after 2sec.
Present Master Card
[Exit programming mode]
5 short beeps after 5sec: cards cleared
1.
1.
2.
2.
3.
3.
4.
4.
MASTER CARD Setting for Stand-Alone
Use the MASTER CARD software
Input the MASTER CARD number, and press [Write].
Cut off and then transmit the power, the master card number will be activated.
Present the card, and the reader will flash green light 3 times and sound 3 beeps. Then the card becomes MASTER CARD and accesses programming
mode.If MASTER CARD is presented again, it will exit programming mode.
Black
Orange
White
Yellow
Converter
Red
[e.g.] No. 154 enable the anti-pass-back, and induction into the door has not been induced to leave. When he represent into the door will become
invalid , then he needs to set the reset. Access programming mode
→
26 00154 00154 2
→
Reset
[e.g.] User address from 00152 to 00684 enable the anti-pass-back function:
26 00152 00684 0
Enable card
Access programming mode
→
26 SSSSS EEEEE N
[SSSSS= User address start; EEEEE= User address end; N=0(control)/ 1(Not control)/ 2(reset)]
D. Lift control
Enable
Access programming mode
→
24 002 [002= enable lift control]
Connect with
AR-401RO16B
to control floors which the user will be able to access.
Plug in cable instead of cable, the wire connection is as below figure. After connection, then have power transmission to controller.
P4
P3
