SOYAL
ACCESS CONTROL SYSTEM
®
AR-327H / AR-727H
V091021
A 18/02 15:45:25
FRI 00001 001
B. Enter/Exit Programming Mode
C. Initial setup
Entering
Input 123456 or PPPPPP (PPPPPP= modified Master Code; Default= 123456)
[e.g.] If the Master Code= 876112, input
876112
→
Programming mode accessed
※
It leaves the programming mode
30
seconds without pushing any button.
Exiting
Press repeatedly
→
Quit
6
Changing the Node ID of Reader
Access programming mode
→
Parameters[1]
→
Node ID
→
Input New Node ID:1~254
(default value:
001)
→
Input: 1~4 to Show Card ID format?
(1.No, 2.WG, 3.ABA, 4.HEX)
→
Input Door number H:
1~254(door No. of its controllen)
→
Input Door number L: 1~254(door No. of reader)
→
Succeeded
[e.g.] AR-327H is the 8th slave reader under the 16th AR-716E.
Door-H
input (door NO. of controller);
Door-L
input (door No. of the reader).
[e.g.] AR-727H is a controller and its Node ID is 8.
Door-H
input ;
Door-L
input
3
1 6
8
8
8
1
Work Status Code
Date
Time
Serial NO.
User Add.
Week
A: Duty On
B: Duty Off
C: Overtime On
D: Overtime Off
E: Break Out
F: Break RTN
G: Out
H: Return
01: PWD/PIN Error
03: Invalid Card
04: Time-zone Error
11: Normal Access
16: Egress (Request to exit)
17: Alarm
31: Anti-pass-back Error
Work Status Code:
Changing the Master Code
Access programming mode
→
Tools
→
Master Code
→
Input the 6-digit new master code
→
Succeeded
5
2
Restoring Factory Settings
Access programming mode
→
Parameters[2]
→
Factory Reset
→
select [1: Yes]
→
Succeeded...
4
9
Review the old events
Access programming mode
→
Tools
→
View Events
→
the display will show the history events.
5
0
Changing the Language
Access programming mode
→
Tools
→
Language
→
EN
→
Succeeded...
5
1
1
Adding and Deleting Tag
Operation
A. Keyboard Lock/ Unlock
Lock/ Unlock
Push both and buttons at same time to lock the keyboard. Push both and at same time again to unlock the keyboard.
Mode4/Mode8
Access programming mode
→
Add/Delete
→
Add Card > ID
→
Input 5-digit user address
→
Input Site Code
→
Input Card Code
1
1
Adding Tag by Tag ID
Access programming mode
→
Add/Delete
→
Delete > Address
→
Input Start address
→
Input End address
1
5
Deleteing User Address
Access programming mode
→
User Setting
→
Password
→
Input 5-digit user address
→
Key in 4-digit PIN
2
1
Setting up the password
Access programming mode
→
User Setting
→
Access Mode
→
Input 5-digit user address
→
1: Card; 2: or PIN; 3: & PIN; 4: Pause;
2
2
Setting up the access mode
Mode6
※
In Mode6, user address is card code. Only suspend or recover to add or delete the tags.
Tag Information
SITE CODE
CARD CODE
SITE CODE
CARD CODE
Access programming mode
→
Add/Delete
→
Add > RF Learn
→
Input 5-digit user address
→
Input Tag Units(pcs)
→
Close Tag into RF Area to induct.
1
2
Adding Tag RF Iduction
※
For a batch of
Sequential tags
, present the tag of the
lowest number
to the controller; for a batch of
non-sequential tags, present all the tags one by one to the controller.
Access programming mode
→
Add/Delete
→
Recover > Address
→
Input Start address
→
Input End address
7
1
Adding Tag
※
For a batch of
Sequential tags
, present the tag of the
lowest number
to the controller; for a batch of non-sequential tags, present all the tags one by
one to the controller.
Access programming mode
→
Add/Delete
→
Suspend > Address
→
Input Start address
→
Input End address
1
3
Deleting Tag
Access programming mode
→
Parameters[1]
→
Arming PWD
→
Input: 0000
3
8
Card Only
Access programming mode
→
Parameters[1]
→
Arming PWD
→
Key in 4-digit PIN [0001~9999, default value: 1234]
3
8
Card and PIN
Access programming mode
→
Parameters[2]
→
Duress Code
→
Key in 4-digit PIN [0001~9999, default value: 4321]
4
8
Card or PIN
※
In this mode, the access controlled by the Arming PWD and Duress Code.