Southworth PLM-100, Руководство пользователя, Страница: 7 / 17

POWERED DANDY LIFTS 7
Model PLM -100 PLM-100W PLM-150 PLM-150W
Capacity 220 lbs 220 lbs 330 lbs 330 lbs
Table Size 20” x 31.5” 24” x 36” 20” x 31.5” 24” x 36”
Raised Height 51” 51” 33.25” 33.25”
Low Height 13” 13” 14.75” 14.75”
Vertical Travel 38” 38” 18.5” 18.5”
Handle Height 37.5” 37.5” 37.5” 37.5”
Overall L x W 20” x 40” 24” x 42” 20” x 40” 24” x 42”
Casters (2) Rigid 5” (2) Rigid 5” (2) Rigid 5” (2) Rigid 5”
Casters (handle end) (2) Swivel 5” (2) Swivel 5” (2) Swivel 5” (2)
Swivel 5”
Floor Lock Yes Yes Yes Yes
Rise Time Empty 21 sec 21 sec 14 sec 14 sec
Rise Time Loaded 26 sec 26 sec 17 sec 17 sec
Lowering Time Empty 21 sec 21 sec 14 sec 14 sec
Lowering Time Loaded 20 sec 20 sec 13 sec 13 sec
Actuator Linear Linear Linear Linear
Battery 24 Volt DC 24 Volt DC 24 Volt DC 24 Volt DC
Charger 115/1/60 115/1/60 115/1/60 115/1/60
Weight 170 lbs 175 lbs 140 lbs 145 lbs
UNPACKING AND
SET-UP OF THE
POWERED DANDY
LIFTS
1) Cut the banding straps and remove
the Powered Dandy Lift Series
from the box. (Make sure all of the
parts are included before the box
is discarded. Figure 1.)
2) Attach the handle to the Powered
Dandy Lift Series by sliding the
two threaded ends of the handle
into the pockets that are welded
to the base frame. Using the lock
washers and the nuts, secure
firmly.
3) After the handle is attached to the
frame the two electrical connections
will need to be attached under the
lift.
TRANSIT DAMAGE
Inspect the Powered Dandy Lift Series
for signs of damage in transit, paying
particular attention to the electrical
cabling. If there is evidence of damage,
contact your Southworth dealer before
using the Powered Dandy Lift Series .
HAZARDOUS
ENVIRONMENTS
The Powered Dandy Lift Series’
electrical equipment is not suitable
for use in flammable or explosive
environments and must never be used
when such hazards exist.
HIGH CYCLE
APPLICATIONS
The Powered Dandy Lift Series is
designed for intermittent use. For high
cycle operations, the following should
be observed:
1) The Powered Dandy Lift Series is
designed to achieve a minimum
life of approximately 10,000 cycles.
For intermittent use, this equates to
many years of service.
2) The Powered Dandy Lift Series
linear actuator should not exceed
six full cycles per hour. The
SPECIFICATIONS
recommended duty cycle for
the actuator motor is 10%. This
means that the motor should not be
operated for more than 6 minutes
of every hour.
OPERATING THE
POWERED DANDY
LIFT SERIES
PLATFORM CONTROL
The position of the platform is controlled
with a push button switch located on
the hand control. The Powered Dandy
Lift Series can be raised by pressing
the UP button on the switch or lowered
by pressing the DOWN button on the
switch.
WARNING!
As the Powered Dandy Lift
Series platform moves up
and down, “pinch points” are
created where the scissor legs
cross, where the legs meet the
base and platform and in the
path on which the rollers travel.
When operating the Powered
Dandy Lift Series , be careful to
ensure that nobody becomes
caught in the moving parts.
BRAKE
The brake prevents the caster from
both swiveling and rolling. Press the
lever located on the top of the caster
to engage the brake.
CAUTION!
The brake is an important
safety device. Please ensure it
is engaged when the Powered
Dandy Lift Series is unattended.
Attempt to find level ground
whenever possible.