background image

• Do not use if any parts are damaged as this can cause an unsafe

condition and lead to tool malfunction or failure.

• If tool is in disrepair, 

DO NOT USE

. Have tool inspected and

repaired prior to use.

5

6

Description of Operation

INTRODUCTION

Description of Operation

FAILURE TO OBSERVE THESE CAUTIONS CAN RESULT IN 

INJURY OR PROPERTY DAMAGE 

    CAUTION:

This manual is provided by Sumner covering the safe operation 

and maintenance procedures for the Sumner LH Series Lever 

Hoists/Pullers. This manual contains instructions on installation, 

safety precautions, general operating procedures, maintenance 

instructions and parts breakdown. This tool has been designed 

and constructed to provide consistent, long-term operation if 

used in accordance with instructions set forth in this manual.

The LH Series hoists are all steel construction with a powder coat 

finish and have a completely enclosed Weston-type automatic 

brake system.   

The LH series hoists are proof-tested and comply with OSHA, 

ANSI/ASME B30.21 and HST-3 standards. 

If there are any questions or comments, please contact either your 

local supplier or Sumner Manufacturing. Sumner can also be 

reached at our web site: www.sumner.com. 

The specifications in this manual were current at time of publica-

tion, but because of our policy of continuous improvement, 

Sumner reserves the right to change specifications at any time 

and without prior notice, without incurring obligations.

• Do not operate hoist unless load is centered between top and

bottom hooks.

• On hoists with the overload warning lever, do not use this device

to measure load weight.

• Always take time to study the job to be performed and choose

the safest method. Do not place yourself or other people in an

unsafe position.

• Always maintain your balance and firm footing when operating

the lever hoist.

• Leave all internal maintenance and inspections to a qualified

Sumner Service Center.

• Do not attempt to lengthen or repair load chain. Replace chain

with factory replacement chain only. Do not use any other type of

chain.

• If welding near the hoist, do not allow the chain or hook to be

touched by a live electrode. Prevent weld splatter upon the chain.

• Never use the hoist if either hook is stretched, deformed, or has

a broken or missing safety latch. Always replace the safety latch

and/or the hook before placing the hoist back in service.

• Be sure supporting structures and load-attaching devices used

in conjunction with this lever hoist provide an adequate safety

factor to handle the rated load plus the weight of the equipment. If

in doubt, consult a qualified structural engineer.

• Keep visitors a safe distance from the work area. Keep children

away.

• Understand and follow all procedures as set forth in American

National Standards titled “Performance Standard for Manually

Lever Operated Chain Hoists,” ANSI/ASME HST-3; and “Manually

Lever Operated Hoists,” ANSI/ASME B30.21. These standards are

available through the American Society of Mechanical Engineers

at www.asme.org.

PURPOSE OF THIS MANUAL

This manual is intended to familiarize all personnel with the safe 

installation and operation of the following: 

STANDARD LEVER OPERATED CHAIN HOIST.

Keep this manual available to all personnel. Replacement manuals 

are available upon request at no charge at www.sumner.com.

FAILURE TO OBSERVE THESE WARNINGS CAN

RESULT IN SEVERE INJURY OR DEATH.

    WARNING:  

This product can expose you to chemicals

including lead, which is known to the State of California to cause 

cancer and birth defects or other reproductive harm. For more 

information go to http://www.p65warnings.ca. gov.

Содержание Sumner LH025















Отзывы: