background image

7

2.  Once locking pin is removed, lift or lower A-frame to 

desired height. Replace locking pin.

3.  Repeat above steps on other A-frame.

CAUTION

It may be necessary to replace  
locking pin and readjust lifting  
handle location in order to properly 
lift or lower A-frame to desired height 
comfortably. Failure to adjust lifting 
handle to a comfortable location for 
lifting may result in injury.

CAUTION

Be certain to check that lift is level 
after adjusting A-frame heights before  
attempting to add a load.

Gantry Span Adjustment

5m and 15 ft GH3/4T Gantry beams have two inner 
span adjustments on each end of the beam. 3m, 4m, 
10 ft and 12 ft Gantry beams have one inner span  
adjustment. Span adjustments are by increments of 
13" (33 cm). 8 ft Gantry beams have no span  
adjustments.

To make span adjustments during assembly, simply 
place the outermost bolt on the A-Frame in the second 
or third inside bolt hole on the beam. It is not neces-
sary to adjust the span symmetrically on either end of 
the beam.

Moving Gantry Lift

CAUTION

It is not recommended to move  
Gantry lift with a load. When  
moving Gantry lift with a load be sure 
to secure trolley in center of cross 
beam and lower load as close to the 
ground as possible prior to moving. 
Move lift by pushing the Gantry, not 
the load. Use caution to avoid the 
load swinging, possibly hitting the 
support structure.

CAUTION

Never move assembled Gantry lift 
with or without a load with a forklift or 
other lifting mechanism.

1.  Adjust A-frame heights to lowest possible position 

prior to moving.

2.  Unlock all casters on both A-frames.

3.  Gantry should be moved with at least two people, 

one on each end. Move by pushing or pulling on the  
Gantry, not the load.

Содержание Sumner GH3/4T-15









Отзывы: