South-Tek Systems N2Blast FPS-900 Скачать руководство пользователя страница 5

 

P

 

The Leader in Nitrogen Generation Technology 

FPS-900 O&M Manual 
Revision: 2; 7/2020 

Page 5 of 29 
 

2.  Safety Guidelines 

 
The following section outlines the basic safety considerations about installation and operation of the 

N

2

-

BLAST

 ®

 FPS-900. For other equipment used with the nitrogen generator, such as air compressors, and 

dryers, refer to the manufacturer’s safety guidelin

es. 

 
2.1  General 

 
Using the 

N

2

-BLAST

®

 FPS-900 correctly is important for safety and trouble-free operation. Wrong use 

can cause damages to the system or can lead to incorrect gas supply. The nitrogen generator produces 
nitrogen at a low flow rate, which quickly dissipates into the air. Nitrogen is not poisonous, but do not 
directly inhale, since high concentrations, can cause asphyxiation.  
 

Warning: Install the unit in a well-ventilated room, one that is sealed off from normal living space 
air changes.

 

 

Read carefully and act accordingly before installing, operating, or repairing the unit: 
 

  The operator must use safe working practices and rules when running the nitrogen generator. 

  The owner is responsible for always keeping the unit in safe working conditions. 

  Always use approved parts when performing maintenance and repairs. Make sure that replacement 

parts meet or exceed the original parts’ specification.

 

  Only competent individuals, train and authorized, can install, operate, perform maintenance and 

repair.   

  Isolate incoming and outgoing pressures to the generator, and depressurize the service or repair 

section before performing any mechanical work, including changing the filters. Vent the nitrogen 

generator’s exhaust gas outside or to a large, well

-ventilated room to avoid suffocation due to lack 

of oxygen. 

 

 

  Wear safety glasses if the cabinet door is open while the machine is running. 

 

  Use ear protection when the equipment is running. 

 

WARNING: Components may experience pressure during operation. Pressurized gases are 
dangerous and may cause injury or death if handled or used inappropriately. 

 

 

Never allow pressurized gas to exhaust from an unsecured hose. An unsecured hose may 
present a whipping action, which can cause serious injury. If a hose burst during use, 
immediately close all isolation valves if safe and turn off the unit.  

 

Never disable or bypass any safety relief valves. 

 

Always disconnect the nitrogen generator the supply power prior to performing electrical 
work. 

 

NOTE: Always follow local and site safety regulations in conjunction with this manual. Correct use of the 
nitrogen generator is important for personal safety. Incorrect safety practices can cause damage to the 
individual and equipment.  

 

Содержание N2Blast FPS-900






























Отзывы: