background image

3.3. Power supply

Mains supply or internal battery powered
Battery:

 rechargeable, 12 V.

Internal battery is useful for up to 

10 A

.

Mains:

 220 - 240 V~  

Mains power is useful for any test current, including 

100 A

.

Make   sure   that   the   voltage   of   the   mains   supply   is
compatible with the voltage supply of the equipment!

Before connecting the equipment to the mains supply, make
sure that the power cord is not damaged. If damaged, do not
connect the equipment to the mains supply and contact the
service center for replacing the power cord.

3.4. Battery condition

The charge condition of the battery can be verified before or during the
resistance measurement. In order to achieve that, the operator  has to
press the 

battery 

button while the equipment is turned on. The bargraph

shows remaining charge as a percentile value. 

If during measurement the charge of the battery achieves a critical level,
the display will show the 

BAT

 message notifying that the charge level is

low.   After   a   few   minutes   the   measurement   will   be   automatically
interrupted in order to preserve the battery from a deep discharge that is
prejudicial for its expected useful life.

9

Содержание 61985






















Отзывы: