Source Technologies Secure MICR Скачать руководство пользователя страница 48

Страница: 48 / 66

Programming Related Errors

Error Message

on Display

Printed

Message

Description

Action

Can’t Create
Node

There was insufficient
memory to track
another audit job

Turn printer off and back
on, then retry. If the
problem recurs, call Tech
Support.

Can’t Purge,
password not
enabled

This error indicates that
MICR mode has not
been enabled.

Press Go. Enter MICR
mode, then re-attempt the
purge.

Can’t Sort
Insufficient
Memory

This error indicates the
printer does not have
sufficient memory to
sort the Audit Report.

Press Go. The printer
may need to be upgraded
with more RAM memory
to sort; otherwise an
unsorted Audit Report
may be printed.

Command
Decode Error

Decode error
&%Sx (where
x is the
incorrect
character)

A syntax error was
detected in a MICR
command.

Check your software for a
syntax error in the MICR
command that was being
used when the error
occurred.

File System
Error Can’t Open
File

There was an internal
error while trying to
access flash for audit
trail

Check that Flash is
installed and not full.

Flash Full Purge
and Format

This error message
indicates that the
printer’s flash memory
is full. The audit trail
cannot accept more
jobs until more space is
available in flash.

Press Go then purge the
audit trail. Then either
defragment or format flash
memory (Utilities Menu).

Integer string
incorrect length

Integer string
incorrect
length

A parameter in a
command was not the
correct length.

Check the Command
(&%STP, STS) for
syntax/numbering errors.

Invalid
AES/DES key

Invalid hex digit or
length of decryption
key

Check the syntax of
SETAESKEY or
SETDESKEY command.

Invalid Convert
to Escape
Character

Invalid
Convert to
Escape
Character

An error was detected
in the User
Programmable Escape
Character Selection
Command. The
software tried to
specify a NULL or an
ampersand as the first
Escape Character.

Check the Command
(&%STY...) for errors.

Error Messages | 8

Source Technologies, LLC ST9720 Secure MICR Printer User’s Guide

Содержание Secure MICR



































































Результаты поиска

Содержание Secure MICR

Отзывы:

Source Technologies Secure MICR, Руководство пользователя, Страница: 48 / 66

Результаты поиска

Содержание Secure MICR

Отзывы: