nFUSE™ LED Lightbar
nFUSE Lightbar English 0520
1.
TABLE OF CONTENTS
PAGE
CONTENT
1
COMPONENTS/ CONTENTS
2
TECHNICAL SPECIFICATIONS
3
POWER SPECIFICATIONS
4-6 MOUNTING
FIXED HEIGHT BRACKETS AND HOOK,
HEADACHE RACK, & PERMANENT MOUNT
7 GASKET MOUNTING INSTRUCTIONS
8-13 ELECTRICAL INSTALLATION
14,15 PHOTO SENSOR
16 CONTROL HARNESS
17,18 LIGHT MODULE LOCATIONS
19 DRIVER MODULE REPLACEMENT
20 NFUSE TROUBLESHOOTING
21 CONNECTION OF BREAKOUT BOX TO SOUNDOFF SIGNAL
SIRENS
22 REPLACEMENT PARTS
23 WARRANTY AND RETURN GOODS PROCEDURE
• To view the full Software Revision History click the in the
upper right hand corner of the SoundOff Lightbar Configurator
application.
• Warning devices are strictly regulated and
governed by Federal, State
and Municipal ordinances. These devices shall be used ONLY on approved
vehicles. It is the sole responsibility of the user of these devices to ensure
compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment
Zone. Refer to your vehicle Owner’s Manual for the location of any air
bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is
self-contained and does not require an external power supply.
Important Information:
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
IMPORTANT NOTICE TO INSTALLER:
Make sure to read and understand all
instructions and warnings before proceeding with the installation of this product.
Ensure that the manual and any warning cards are delivered to the end user of
this equipment. Proper installation of the lightbar requires the installer to have
a thorough knowledge of automotive electronics, systems, and procedures.
Lightbars provide an essential function of an effective visual warning system.
The use of the lightbar does not insure that all drivers can or will abide by or
react to an emergency warning signal, especially at high rates of speeds or
long distances. The operator of the vehicle must never take the right of way for
granted and it is the operator’s responsibility to proceed safely. The effectiveness
of the lightbar is highly dependant on the correct mounting and wiring. The
installer must read and follow the manufacturer’s installation instructions and
warnings in the manual. The vehicle operator should verify daily that the lightbar
is securely fastened to the vehicle and properly functioning before operating
vehicle. The lightbar is intended for use by authorized personnel only. It is the
user’s responsibility to ensure they understand and operate the emergency
warning devices in compliance with the applicable city, state and federal laws
and regulations. SoundOff Signal assumes no liability for any loss resulting from
the use of this warning device.
Components/Contents
Standard Equipment:
1 - nFUSE™ LED Lightbar built to your specifications
1 - Breakout Box
1 - 24 Pin Harness
Other Parts that may be included depending on your configuration:
1 - Vehicle Specific Hook Kit w/ Hardware*
2 - Fixed Height Mounting Brackets w/ Hardware or
1 - Flat Mount Hardware Kit or
2 - Headache Brackets w/ Hardware
*Kits will vary with each lightbar depending on vehicle specified on order form.
Unpack Lightbar
1. Remove the lightbar from box and packaging.
2. Save packaging for later shipping.
3. Check components/contents.
4. Please reference these instructions for proper wiring and installation.
Tools Required for Installation
• 7/16“ Socket with ratchet
• Phillips Head Screwdriver
• Drill bit #30
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/tech-services/returns/
.
If you have questions regarding this product, contact
Technical Services
, Monday - Friday, 8 a.m. to 5 p.m. ET at
1.800.338.7337
(press #4).
Questions or comments that do not require immediate attention may be emailed to
ENHANCING SAFETY THROUGH INNOVATION
FRONT
GASKET MOUNTING INSTRUCTIONS
LED MODULE
6 LED SINGLE COLOR
12 LED DUAL COLOR
A
A
B
B
C
C
D
D
E
E
F
F
ENULBXXXXXXX
SHEET
