background image

7X3 / 6X4  P SERIES_STT

  00KPJL 0822  REV B

1.800.338.7337 / www.soundoffsignal.com

P SERIES STOP/TAIL & TURN LIGHTS

EPSSC0JY(x)-(x) -- 7X3 Screw Mount & Stud Mount

EPSSBOJX(x)-(x) -- 6X4 Screw Mount & Stud Mount

• HIGH CURRENT interconnects must be properly terminated. Poor crimp 

quality can cause heat build-up and fire. Follow the crimp connector  

manufacturer instructions.

• DO NOT install this product or route any wires in the Air Bag Deployment 

 Zone. Refer to vehicle Owner’s Manual for deployment zones.

• Do NOT use system to disconnect headlights, brake lights or other safety 

 equipment.

• Unit may become hot to touch during normal operation.

• Failure to properly install connectors, fuses or wiring may cause vehicle 

 failure or fire.

• Installation must only be performed by trained technician. Installer must 

 determine vehicle wiring configuration and proper integration of system.

• Use proper wire gauge.  All power wires connecting to positive (+) or 

 negative (-) battery terminal or local chassis ground (-) must be sized to  

 supply at least 125% of max. current and properly fused at power source.

• Install protective grommets when routing wire through firewall or metal.

WARNING

!

ROUTE WIRES ONLY IN LOCATIONS THAT ARE NOT SUBJECTED TO 

POTENTIAL WEAR. MAKE SURE TO AVOID ROUTING WIRES IN THE 

DEPLOYMENT AREA OF YOUR AIR BAG. REFER TO YOUR VEHICLE'S 

OWNER'S MANUAL FOR AIRBAG DEPLOYMENT ZONES.  

WARNING

Protected by U.S. Patent 10,703,260 and Patents Pending

 https://soundoffsignal.com/legal/patent-notification/

DIMENSIONS . . . . . . . . . . . . . . . . . . 2
STOP/TAIL & TURN  LIGHT OPTIONS . . 2
TECHNICAL SPECIFICATIONS . . . . . . 3
WIRING INFORMATION . . . . . . . . 4-5
STUD MOUNT INSTALLATION . . . . . 6
SCREW MOUNT INSTALLATION . . . . 7
RETENTION CLIP INSTRUCTIONS . . . 8

7x3 Stop/Tail Shown

6x4 Stop/Tail Shown

NOTICE: 

Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning 

devices. 

Improper use or installation may void warranty coverage.To review our Limited Warranty Statement & Return Policy 

for this or any SoundOff Signal product, visit our website at 

www.soundoffsignal.com/tech-services/returns/

. If you have 

questions regarding this product, contact 

Technical Services

, Monday - Friday, 8 a.m. to 5 p.m. ET at 

1.800.338.7337

 (press 

#4). Questions or comments that do not require immediate attention may be emailed to 

[email protected].

 

 

ENHANCING SAFETY THROUGH INNOVATION

Содержание EPSSC0JY Series









Отзывы: