Sound Performance Lab 9737 Скачать руководство пользователя страница 11

Страница: 11 / 16

Machine Head

Storing a preset:

Depress S

TORE

for1 sec.,

LED flashes;
use U

OWN

to select

preset no.;
depress S

TORE

again,

LED goes out, preset is
stored

Applying a preset:

Depress A

PPLY

for1 sec.,

LED flashes;
use U

OWN

to select

preset no.;
depress A

PPLY

again,

LED goes out, preset is
applied

Operation safety:
Presets can not be changed
by accident

The D

RIVE

EVEL

metering shows the recording level of the

“virtual tape machine”. The display range is -10 dB to +21 dB.
The D

RIVE

EVEL

ist adjusted with the D

IRVE

control (see 3).

The O

UTPUT

PPM meters show the peak level after the O

UTPUT

AIN

control (see 5).

The first LED in each I

NPUT

and O

UTPUT

PPM meter is a signal

.) LED to indicate that a valid digital source is connected and

detected. This LED helps you to verify the signal flow within a
digital processing chain. If one S

. LED is not illuminating you

have a first indication of a faulty digital signal flow.

The last LED of each I

NPUT

and O

UTPUT

PPM meter is a C

LIP

LED. The LED illuminates if the digital signal is too hot causing
digital distortion.

The M

ACHINE

EAD

allows you to store up to 99 presets, which

can be changed by MIDI program change command.

If you want to store a new adjustment, depress S

TORE

for one

second. The LED starts to flash indicating that the S

TORE

mode

has been activated. The LC-display now shows the values of the
presets (including the B

OOST

function) before the M

ACHINE

EAD

was switched off the last time. Use U

and D

OWN

to select a

new preset number. The status-LED flashes shortly to indicate
that the input (depressing U

or D

OWN

) is accepted. Keeping U

or D

OWN

depressed will let you jump through the preset list in

steps of 5 presets. Once a new preset location is found depress
S

TORE

again. The S

TORE

LED goes out. The preset is stored at the

new location.

In case you want to quit the S

TORE

mode without storing the

new adjustments simply press A

PPLY

If you want to apply various presets depress A

PPLY

for one

second. The A

PPLY

LED starts to flash indicating that the A

PPLY

mode is activated. You can step through the preset list with U

and D

OWN

. Once you have a preset that you want to apply

depress A

PPLY

again. The A

PPLY

LED goes out indicating that the

preset is applied.

In case you want to quit the A

PPLY

mode without applying the

new preset simply press S

TORE

NOTE: To increase operation safety it is impossible to apply

presets by simply depressing U

or D

OWN

. The U

and D

OWN

status-LEDs will not flash indicating that the input is not
accepted. You have to depress S

TORE

or A

PPLY

for one second in

order to activate the U

and D

OWN

buttons.

Presets

Control Elements

Содержание 9737

















Результаты поиска

Содержание 9737

Отзывы:

Бренды по названию

Популярные бренды

Sound Performance Lab 9737, Руководство пользователя

Результаты поиска

Содержание 9737

Отзывы:

Бренды по названию

Популярные бренды