Sound Performance Lab 9737 Скачать руководство пользователя страница 10

Страница: 10 / 16

Machine Head

UTPUT

AIN

varies the output level of the digital data stream.

It is variable between -12 dB and +12 dB in 0.1 dB steps.

The adjusted O

UTPUT

AIN

value is shown in the LC-display

(see 7) and in the O

UTPUT

PPM meter (see 8).

In practice you will start with the

OUTPUT

AIN

set to 0 dB. In

case you have used high D

RIVE

values you will use the O

UTPUT

AIN

to compensate for the slight level increase.

You can also use the O

UTPUT

AIN

control to compensate for

the loudness difference between unprocessed and processed
signal to judge upon the sonic effect alone. After you have
reduced the O

UTPUT

AIN

until original and processed signal

have the same loudness you can readout the loudness increase
on the O

UTPUT

PPM meters compared to the I

NPUT

PPM meters.

Also, if you have chosen a positve setting on the HF-A

DJUST

control, it may be necessary to reduce the O

UTPUT

AIN

slightly

in order to prevent clipping. Watch the C

LIP

-LED

You will set a positive O

UTPUT

AIN

, when there is still

headroom left after processing. Always check this on the
loudest part of the audio file being processed and watch the
C

LIP

-LEDs.

With the H

IGH

APE

PEED

switch you can change the speed of

the vitual tape from standard tape speed (15 ips) to high tape
speed (30 ips).

When H

IGH

APE

PEED

is activated the algorithm simulates

the pre-emphasis for high speed recording. The upper mid and
high frequencies as well as the harmonical content gain better
resolution and finer detail.

Note that the 40 Hz to 70 Hz bass-reduction induced when

recording to analog tape at 30 ips is not reproduced!

The LC-display shows all encoder settings and the number of

the preset being used in the last session with the M

ACHINE

EAD

(for details on P

RESETS

refer to 9).

More information is displayed when activating the I

NFO

pages

(see 10). Press S

TORE

and A

PPLY

for 1 sec. to enter the I

NFO

pages.

The I

NPUT

and O

UTPUT

LED chains are PPM (peak level) meters

with signal and clip indicators. The metering offers 1 dB resol-
tion for the last 3 dB before 0 dB.

The I

NPUT

PPM meters show the peak level after the I

NPUT

AIN

control (see 2).

Control Elements

Compensating a level
and/or loudness increase
due to processing

Gaining a finer high
frequency resolution when
selecting H

IGH

APE

PEED

Output Gain

High Tape Speed

LC-display

LED chains

Содержание 9737

















Результаты поиска

Содержание 9737

Отзывы:

Бренды по названию

Популярные бренды

Sound Performance Lab 9737, Руководство пользователя

Результаты поиска

Содержание 9737

Отзывы:

Бренды по названию

Популярные бренды