background image

The LED Light on the Charger 

 
 
 
 
 
 

 

  Power On (Green light flashes slowly) 

  Battery Low (Red light stays illuminated) 

  Battery charged 80% (Green light flashes rapidly) 

  Battery charged 100% (Green light stays illuminated) 

  Battery Pack temperature is too hot or too cold (Red light flashes slowly) 

  Battery Pack malfunction (Red and Green lights stay illuminated) 

 

!   WARNING 

1. Charger is plugged into a 110V-120V a.c outlet only. 
2. If the battery pack is too hot or too cold, the charger will not fast charge the 

battery  pack  and  the  red  Indicator  light  is  “blinking”.  When  the  battery  pack 
temperature returns to between 0°C(32°F) and 50°C(122°F), The charger will 
automatically begin charging. 

3. 

If both red and green indicator lights are “ON” the battery pack either does not 
comply or is defective. Please contact your retailer. 

4. Do  not  charge  the  battery  pack  in  the  rain,  snow  or  high  temperature 

environment. 

5. Do  not  charge  battery  pack  when  environment  temperature  is  below 

0°C(32

°

F)or above 40

°

C(104°F) 

6. While charge the cool battery pack (below 0°C) in the warm indoor, keep the 

battery pack in the room for one hour to warm up before starting the battery 
pack. 
A cool battery may charge unsaturated. 

7. Remove the plug after finishing the charge.

 

8. Do not use generator for charging the battery pack.

 

Содержание HPS-4C2-10.8V Li-Ion













Отзывы:

Похожие инструкции для HPS-4C2-10.8V Li-Ion