SOR 1267AFR-1 Скачать руководство пользователя страница 1

Form 1630 (09.18) ©SOR Inc. 

1/8

The 1267 Air Filter Regulator is designed for air or 
gas service. Maximum allowable inlet pressure is 
250 psi (17 bar). Operating temperatures are 0°F 
to 160°F (-18°C to 71°C). The 1267AFR has low 
capacity internal relief which provides very limited 
downstream overpressure protection.

1267AFR

Air Filter Regulator

  General Instructions

Registered Quality System to ISO 9001

Design and 

specifications are 

subject to change 

without notice. 

For latest revision, go to 

sorinc.com

NOTE: If you suspect that a product is defective, contact the factory or the SOR

®

 Representative 

in your area for a return material authorization number (RMA). This product should only be 
installed by trained and competent personnel.

Table of Contents

Installation .......................................2
Calibration .......................................2
Maintenance .....................................3
Specifi cations ...................................4
Materials .........................................4 
Parts List .........................................5
Dimensions ................................... 6-7

The internal relief valve in the 1267AFR does 
not provide full overpressure protection and 
is designed for minor seat leakage only. To 
avoid exceeding outlet pressure limits in 
service, a pressure-relieving or pressure-
limiting device should be provided. Leakage, 
equipment damage, or personal injury can 
result from over-pressuring the regulator.

All SOR instructions, as well as applicable local, state, and federal codes 
and regulations should be adhered to when performing installation, 
operation, or maintenance of a regulator. Personal injury, equipment 
damage, or leakage can occur if the regulator is over-pressured or physically 
damaged. To avoid physical damage the regulator should be installed in a 
safe location. The regulator shouldn’t be installed in systems that exceed 
the specifi ed pressure limit of 250 psi (17 bar). If leakage develops, then 
maintenance is required. Failure to remove the regulator from service 
immediately may create a hazardous situation.

T bl

f C

t

t

es 

e, 

Содержание 1267AFR-1









Отзывы: