Sony XTL-750W, Руководство по обслуживанию

Страница: 12 / 46

– 12 –
2.5 Vp-p
0 V
• Use the following equipment for the electrical adjustment.
Equipment
1
Monitor TV (XVM-750W, etc.)
2
Spectrum analyzer
3
TV signal generator
4
Digital voltmeter
5
Oscilloscope
6
Audio analyzer
7
DC power supply
8
Frequency counter
Equipment Connections
Connect the test equipment as shown in the figure below (unless
otherwise instructed) and perform the adjustment.
Setup during Adjustment
Use the video signal obtained from the TV signal generator as the
alignment signal, and check that this signal is within video output
signal standards.
TRAP Adjustment (Hong Kong model)
Procedure:
1. With the Power off, input the output of TG to TP30 (with DC
cut by a capacitor (0.01
µ
F)).
2. Connect a spectrum analyzer to TP31 (with DC cut by a
capacitor (0.01
µ
F)).
3. Adjust T1 so that the waveform peak is 39.75 MHz
±
50 Hz.
4. Adjust T2 so that the waveform peak is 30.0 MHz
±
50 Hz.
5. After this adjustment, open TP30 and TP31. (Disconnect the
spectrum analyzer.)
VCO Adjustment
Procedure:
1. No connection to ANT IN. (no signal state)
2. Connect a resistor (10 k
Ω
) between TP33 and +9 V (TP35).
3. Connect a spectrum analyzer to TP34 (with DC cut by a
capacitor (0.01
µ
F)).
4. Adjust T3 so that the waveform peak is 38.0 MHz
±
1 kHz
(Hong Kong model) or 45.75 MHz
±
1 kHz (US model).
5. After this adjustment, open TP34. (Disconnect the spectrum
analyzer.)
AGC Adjustment
Procedure:
1. Set the TV SYSTEM switch to 1.
2. Input a color bar signal of C9ch (192.25 MHz) (Hong Kong
model) or 10ch (193.25 MHz) (US model) and 66 dB
µ
V
(75
Ω
OPEN).
3. Connect the digital voltmeter to TP42.
4. Adjust VR1 so that reading on the digital voltmeter is
6.0
±
0.1 V (Hong Kong model) or 3.0
±
0.1 V (US model).
AFT Adjustment
Procedure:
1. Input a color bar signal of C9ch (192.25 MHz) (Hong Kong
model) or 10ch (193.25 MHz) (US model) and 74 dB
µ
V
(75
Ω
OPEN).
2. Connect the oscilloscope to TP102.
3. Adjust T3 untill the waveform on the oscilloscope is 2.5 Vp-p.
38.0 MHz (Hong Kong model)
45.75 MHz (US model)
T1= 39.75 MHz
T2= 30.0 MHz
0.7 V
0.3 V
0.3 V
red
white (approx. 100%)
horizontal sync. signal
burst signal (flat)
TV SG
set
POWER (CN4)
RF out
ANT IN
DC
power supply
TUNER UNIT SECTION
Color bar signal from TV signal generator (US model)
Note: Small peaks (dips) coming out from the top of the
waveform are unacceptable.
Connection points: See page 14.
Adjustment points: See page 14.
0.7 V
0.3 V
0.3 V
red
white (approx. 100%)
horizontal sync. signal
burst signal (flat)
Color bar signal from TV signal generator (Hong Kong model)