Sony XPlod MEX-BT5000, Руководство по обслуживанию

Страница: 14 / 88

14
MEX-BT5000
(AEP, UK)
Cautions
Be sure to install this unit in the dashboard of the car as
the rear side of the unit becomes hot during use.
•
This unit is designed for negative earth 12 V DC operation
only.
•
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
•
Before making connections, turn the car ignition off to
avoid short circuits.
•
Connect the power connecting lead
3
to the unit and
speakers before connecting it to the auxiliary power
connector.
•
Run all earth leads to a common earth point.
•
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
•
Do not cover the ventilation slots or heat sinks of the unit.
Notes on the power supply lead (yellow)
•
When connecting this unit in combination with other
stereo components, the connected car circuit’s rating must
be higher than the sum of each component’s fuse.
•
When no car circuits are rated high enough, connect the
unit directly to the battery.
Connection example
Notes (
2
-A)
•
Be sure to connect the earth lead before connecting the amplifi er.
•
The alarm will only sound if the built-in amplifi er is used.
Tip ( 2 -B- )
For connecting two or more CD/MD changers, the source selector
XA-C40 (not supplied) is necessary.
Connection diagram
A To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
B To the interface cable of a car telephone
Warning
If you have a power aerial without a relay box, connecting
this unit with the supplied power connecting lead
3
may
damage the aerial.
Notes on the control power and suppy leads
•
The power aerial control lead (blue) su12 V DC when
you turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffi c Announcement) function.
•
When your car has built-in FM/MW/LW aerial in the rear/side
glass, connect the power aerial control lead (blue) or the
accessory power input lead (red) to the power terminal of the
existing aerial booster. For details, consult your dealer.
•
A power aerial without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
•
Before connecting the speakers, turn the unit off.
•
Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
•
Do not connect the speaker terminals to the car chassis,
or connect the terminals of the right speakers with those
of the left speaker.
•
Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
•
Do not attempt to connect the speakers in parallel.
•
Connect only passive speakers. Connecting active
speakers (with built-in amplifi ers) to the speaker terminals
may damage the unit.
•
To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
•
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker
and amplifi er are connected correctly.
L
R
AUDIO
OUT
REAR
AUDIO
OUT
FRONT
BUS
AUDIO
IN
5 7
4 8
1 3 5 7
2 4 6 8
A
B
6
AUDIO OUT
REAR
BUS
CONTROL IN
REMOTE
IN
AUDIO OUT
FRONT
BUS AUDIO IN/
AUX IN
* 3
SUB OUT (MONO)
Supplied with the CD/MD changer
2
* 1
from car aerial
Fuse (10 A)
3
AMP REM
Light blue
Blue/white striped
from the car’s power connector
ATT
See “Power connection diagram” on the reverse side for details.
Max. supply current 0.3 A
* 2
* 5
Negative polarity positions 2, 4, 6, and 8 have striped leads.
1
Purple
+
Speaker, Rear, Right
5
White
+
Speaker, Front, Left
2 Speaker, Rear, Right 6 Speaker, Front, Left
3
Grey
+ Speaker, Front, Right 7
Green
+ Speaker, Rear, Left
4
Speaker, Front, Right
8 –
Speaker, Rear, Left
* 2
Source selector
(not supplied)
XA-C40
from the car’s speaker connector
Positions 1, 2 and 3 do not have pins.
4 Yellow continuous power supply
5 Blue power aerial control
6 Orange/White switched illumination power supply
7 Red switched power supply
8 Black earth
* 2
* 7
* 6
* 7
* 1
Note for the aerial connecting
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor
2
to connect it. First connect
the car aerial to the supplied adaptor, then
connect it to the aerial jack of the master unit.
* 2 RCA pin cord (not supplied)
* 3 Be sure to match the colour-coded cord for
audio to the appropriate jacks from the unit. If
you connect an optional CD/MD changer, you
cannot use AUX IN terminal.
* 4
Auxiliary equipment such as portable DVD
player (not supplied)
* 5
Supplied with the auxiliary equipment
*
6
Insert with the cord upwards
* 7 Supplied with XA-C40
*
4
–
–
–
S
UB OUT (MONO)
AUDIO OUT
REAR
AUDIO OUT
FRONT
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
A
B
*
not supplied
Source selector
*
XA-C40