Sony XPERIA Ion LT28at Скачать руководство пользователя страница 171

Страница: 171 / 224

Troubleshooting Guide (mech)

1261-4721 Rev 3



Sony Mobile Communications AB

– Company Internal

38(62)

Problem Areas

1.18 Ambient Light Sensor

1.18.1 Light Sensor malfunctions

Check:

Inspect the external window area of light sensor on the
Cover Front Assy.

Action:

1. If clogged

– clean it.

2. If scratched or damaged

– replace the Cover Front Assy.

Note: Ensure the BtB connector of battery is
disconnected in the following steps!

Check:

Inspect the both sides of the ZIF connector on the Main PBA
and the FPC Top Flex.

Action:

1. If not properly connected

– disconnect and reconnect.

2. If dirty or oxidized

– clean it.

Check:

Inspect the light sensor on the FPC Top Flex.

Action:

1. If dirty

– clean it.

2. If the light sensor or the connector is damaged

– replace

the FPC Top Flex.

3. Replace board.

Содержание XPERIA Ion LT28at

































































































































































































































Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды

Sony XPERIA Ion LT28at, Руководство по эксплуатации

Результаты поиска

Содержание XPERIA Ion LT28at

Отзывы:

Похожие инструкции для XPERIA Ion LT28at

Бренды по названию

Популярные бренды