31
XCG-CP510/XPL-SDKW
2020
Digital V
ideo Camera (GS
CMOS)
Digital V
ideo Camera (CCD)
Accessories
XCL
XCL
FCB-4K
FCB-HD
Color Camera B
loc
k
XCG
XCU
Polarization
Camera
1
3
2
5
4
Trigger input polarity = Negative
Trigger input polarity = Positive
2.0 µs or less
10 µs to 2 s
2.0 µs or less
1 frame time or more
0 to 0.4 V
2.0 µs or less
10 µs to 2 s
2.0 µs or less
1 frame time or more
0 to 0.4 V
5 to 24 V (DC IN
connector 2nd pin)
3.5 to 5.5 V (DC IN
connector 3rd and
4th pins*)
5 to 24 V (DC IN
connector 2nd pin)
3.5 to 5.5 V (DC IN
connector 3rd and
4th pins*)
* Except XCG-CG160/CG160C
5 V to 24 V
0 V to +0.4 V
10 μs to 2 s
2.0 µs
or less
2.0 µs or less
5 V to 24 V
0 V to 0.4 V
10 µs to 2 s
2.0 µs
or less
2.0 µs or less
Connect the camera cable to the DC IN connector and connect the
LAN cable to the RJ45 connector respectively. If you use a camera
module interface board or a hub that supports PoE, you can
operate the camera even if you do not connect the camera cable
to the DC IN connector. When you connect the LAN cable with
fastening screws, turn the two screws on the connector to secure
the cable tightly.
Connect the other end of the camera cable to the DC-700/700CE
and the other end of the LAN cable to the camera module interface
board or a hub.
1
RJ45 connector
2
DC IN connector
3
LAN cable
4
Fastening screws
5
Camera cable
Do not supply power to the camera cable and LAN cable
at the same time.
Connecting the Cables
Note
Control functions
Description
Operating mode
Free run/Trigger
Free run
1/100,000 s to 60 s
Trigger edge
detection
1/100,000 s to 60 s
Trigger pulse
width detection
Setting by trigger pulse width
Gain
0 dB to 18 dB
Partial Scan
Variable, 4-line increments
(the number of settable lines are 16 or more)
LUT (Look Up Table)
OFF/ON (Mode: 5 types)
External trigger input
DC IN connector
Video output switch
Monochrome model: Mono 8 / 10 / 12 bit
Defect correction
OFF/ON
Shading correction
OFF/ON
Image flip
OFF/ON
Area gain
OFF/ON
Controlling the Camera From the Host Device
Trigger signal polarity
Positive refers to a trigger signal polarity activated while rising from
Low to Hi, or during the Hi interval.
Negative refers to a trigger signal polarity activated while falling
from Hi to Low, or during the Low interval.
DC IN connector specifications
Register
Parameter
Setting
Trigger Activation
FallingEdge (0)
Negative
RisingEdge (1)
Positive
Trigger signals can be input via the 2nd, 3rd, 4th pins of the DC IN
connector, or the software command. Switchover of the trigger
signal can be changed via the TriggerSource register.
* XCG-CG160/CG160C: Unavailable. Dedicated to output.
Register
Parameter
Setting
Trigger
Source
Line1 (0)
DC IN connector 2nd pin (GPI1)
Line2 (1)
DC IN connector 3rd pin (GPI2)
Line3 (2)
DC IN connector 4th pin (GPI3) *
Software (4)
Software (TriggerSoftware register)
FreeSetSequence (13)
FreeSetSequence mode
PTP (15)
IEEE1588 synchronization mode
Trigger Signal Input
• When inputting a trigger signal to the camera using the DC-
700/CE, use DC 5 V or less at the logical high level.
• Make sure to supply power to the camera module and confirm
that the camera module is operating before inputting a trigger
signal. If you input trigger signal to a camera module without
the power supplied, this may cause a malfunction of the
camera module.
Note
Trigger Signal Specifications
Trigger input polarity = Positive
Trigger input polarity = Negative
Voltage reading shows figure by terminal with 10 kΩ or more.
When inputting a trigger signal to the camera using the DC-700/DC-
700CE, use DC 5 V or less at the logical high level.
Note
