
1-4
WRR-862A/862B
9
(GB)
6
When the desired group appears, press the SET button
again.
The group selected is fixed.
The tuner now enters the wireless channel setting mode,
and both of the TV channel number and 2-digit number
flash on the display.
7
Press the + or – button to select the desired wireless
channel.
The wireless channels change in the order listed on the
table of the group on the “Wireless Microphone System
Frequency List” supplied with this manual.
8
When the desired wireless channel appears, press the
SET button.
The display stops flashing and the selected group and
wireless channel are now stored in memory.
Display example for U66 model
Channel setting
To select the channel by frequency indication
1
Turn on the unit, select the tuner to be set.
2
Press the MODE button until the frequency indication
appears.
3
Press the SET button.
The frequency indication starts flashing.
4
Press the + or – button to select the desired channel
frequency.
5
When the desired frequency appears, press the SET
button.
The display stops flashing and the selected wireless
channel is now stored in memory.
If noise is heard
Depending on the environment where the system is installed,
outside noise or radio wave may disrupt the transmission of
certain channels.
To select a channel under this circumstance, turn off the
wireless microphone or transmitter. Then select a channel at
When the group 00 is selected for U66 model
Display example for U66 model
10
(GB)
Settings
other. In such a case, keep a enough distance to ensure
the proper performance of the unit.
•
When operating two or more UHF wireless microphone
systems using channels in different groups, ensure that the
systems are at least 100 m (330 feet) apart from each
other. (The same applies also when using channels in a
group if the different UHF wireless microphone systems
are installed where they are within sight of each other.)
Setting the Squelch Level
You can eliminate the noise and signal interference which
may occur in reception stand-by mode. Select a squelch
level from 5 dB
µ
, 10 dB
µ
or 15 dB
µ
. The factory preset
level is 10 dB
µ
. To obtain a wide service area, set this to
5 dB
µ
. When using the tuner in a multi-channel system or
when you want to receive noise free audio input all the time,
set it to 15 dB
µ
.
1
Press the MODE button until the squelch level appears.
2
Press the SET button.
The squelch level indication starts flashing.
which the RF indicator is off. (A channel free from noise or
radio wave interference is selected.) Set the same channel on
the microphone or transmitter.
Notes
•
Do not remove the batteries during group and wireless
channel selection. If they are inadvertently removed, re-
insert them immediately and repeat the steps on pages 7 to
9 from the beginning.
•
Make sure that the channel selected is the same as that
selected on the transmitter used in the same system.
•
Be sure to set tuners 1 and 2 to different channels.
•
Depending on the noise or interference conditions, the
selectable channels may not necessarily all be usable. If
necessary, you can determine the usable channels by
stepping the channel selection through a number of
channels on the tuner with the microphone/transmitter set
to OFF. Those channels on which the RF indicator of the
tuner does not light are usable.
•
If there is a TV broadcasting station near by, do not use
the station's channel.
•
The unit may not operate correctly if it is turned on again
immediately after turning off the power while in setting
mode. Pause for a few seconds or more before turning on
the power again.
•
When operating the unit with one transmitter (for
example, using tuner 1 for reception, and leaving tuner 2
unused), noise or audio signals may occur on the unused
tuner, if the tuner and the transmitter are too close to each
Squelch level
11
(GB)
3
Press the + or – button to select the desired level.
4
When the desired level appears, press the SET button.
The display stops flashing and the selected level is now
stored in memory.
Squelch functions
When the SQUELCH switch is set to ON, the following functions
work in combination.
(1) Squelching by RF input level
As sufficient S/N for the audio output may not be obtained if no RF
signal is received or the RF input level is low, the audio output is
squelched when the RF input level falls below the squelch level
selected
.
(2) Tone squelch
The audio output is obtained only when the unit receives an RF
signal which includes a specified tone signal. The audio output is
squelched to eliminate noise which may be heard when the
transmitter is turned on/off or the unit receives an interference RF
signal.
(3) Noise squelch
The audio output is squelched to eliminate noise which may be
heard when there is such excessive interference RF signal that the
tone squelch does not work.
Accumulated time of
battery use
Resetting the Accumulated Time Indication
The time indication accumulates time in hours and minutes
when the WRR-862A/862B is on.
Reset the indication to “00:00” whenever you replace the
batteries so that it can display the running time of the
batteries.
1
Press the MODE button until the accumulated time
appears.
2
Press the SET button.
3
Press the – button.
The time indication resets to “00:00.”
While you see “00:00” is flashing, you can go back to
previous value by pressing the + button.
4
Press the SET button.
12
(GB)
Error Messages
Backlight mode
Selecting the Backlight Mode
You can select the backlight mode of the display.
1
Press the MODE button until the backlight mode appears.
2
Press the SET button.
The backlight indication starts flashing.
3
Press the + or – button to select the desired mode.
BL OFF : Lights off all the time
BL ON : Lights on all the time
BL AT : Lights on when you begin to operate the
tuner. Turns off automatically 15 seconds
after you finish operation.
4
When the desired mode appears, press the SET button.
The display stops flashing and the selected mode is now
stored in memory.
When a problem occurs, one of the following error message
may appear on the display.
Messages
ERROR 03
ERROR 11
ERROR 21
ERROR 51
Contents
The battery voltage
exceeds the allowable
value.
An error occurred in
backup memory data.
The PLL synthesized
circuit is in trouble.
Defect of the A/D
converter.
Measures
Use the specified
batteries.
Contact your Sony
dealer.
Settings
Содержание WRR-862A
