Speed dialing
You can dial with a touch of a few keys by storing a phone number on a dialing key.
Storing phone numbers
Note
Do not allow more than 20 seconds to elapse between each step
of the procedure.
Tips
• If you enter a wrong number, press
(PGM)
, then start from
the beginning.
• You can attach the supplied directory on the handset.
To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2
Press
(REDIAL/PAUSE)
.
To change a stored number
Store a new number, as described previously.
Note
You can replace the stored number with a new number, but you cannot just erase it.
Making calls with speed dialing
1
Press
(TALK)
and wait until the TALK/BATT LOW lamp lights up.
The dialing keys light up.
2
Press
(SPEED DIAL)
.
3
Enter the desired speed dialing number (
(0)
to
(9)
).
The phone number stored in the speed dialing number will be dialed.
Paging
You can page the handset from the base unit. Note that you cannot page if the handset
is in use.
Resetting the digital security code
The first time you charge the battery pack, a random security code is automatically
assigned between the base unit and the handset. Only a handset which has this
security code can make calls through the base unit. This system prevents the
possibility of other cordless telephone handsets making calls through your base unit.
You normally do not need to reset the security code. However, in the unlikely event
that you suspect that another cordless phone uses the same security code, you can
manually change the code. Pick up the handset from the base unit, and proceed as
follows:
Note
If the battery pack in the handset is completely discharged, or is removed from the handset for
more than several seconds, the digital security code stored will be lost. If this happens, charge the
battery pack and a new security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset. The code can be
changed as often as desired.
Mounting the base unit on a wall
1
Attach the telephone line cord and AC power adaptor cord to the base
unit. Bundle the loose telephone line cord or AC power adaptor cord, if
necessary.
2
Plug the telephone line cord into the telephone outlet, and hook the base
unit to the wall plate as illustrated.
1
Press
(PGM)
.
The TALK/BATT LOW lamp
flashes.
2
Press
(SPEED DIAL)
.
The dialing keys light up.
3
Press one of the dialing keys (
(0)
to
(9)
) to store a phone number
on.
You hear a confirmation beep.
4
Enter the phone number you want
to store.
You can enter up to 20 digits,
including a tone and a pause, each
of which is counted as one digit.
5
Press
(PGM)
.
You hear a long confirmation
beep, and number is stored. The
TALK/BATT LOW lamp goes off.
Press
(HANDSET LOCATOR)
.
The handset rings for about one
minute.
To end the page, press
(OFF)
on
the handset.
2
1, 5
(REDIAL/PAUSE)
TALK/BATT
LOW lamp
(HANDSET LOCATOR)
1
Press
(PGM)
.
The TALK/BATT LOW lamp
flashes.
2
Press
(#)
.
You hear a confirmation beep.
The dialing keys light up.
3
Press three of the dialing keys
(001 to 999) to store a new code.
4
Press
(PGM)
.
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.
5
Immediately replace the handset
on the base unit.
You hear a long confirmation
beep and the phone stores the
new code.
1, 4
2
TALK/BATT
LOW lamp
1
2
AC power
adaptor cord
Telephone
line cord
Bundle the loose
telephone line cord
or AC power
adaptor cord, if
necessary.
Wall plate
AC power
adaptor
AC outlet
