background image

Introduction

2

WARNING

To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
The mains lead must only be changed at a
qualified service shop.

Precautions

Safety

• This unit operates on 110 – 240 V AC, 50/60

Hz. Check that the unit’s operating voltage
is identical with your local power supply.

• If anything falls into the cabinet, unplug the

unit and have it checked by qualified
personnel before operating it any further.

• The unit is not disconnected from the mains

as long as it is connected to the mains, even
if the unit itself has been turned off.

• Unplug the unit from the mains if you do

not intend to use it for an extended period of
time. To disconnect the lead, pull it out by
the plug, never by the lead.

Installing

• Allow adequate air circulation to prevent

internal heat buildup.

• Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation
slots.

• Do not install the unit near heat sources

such as radiators or air ducts, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration or shock.

• Do not install the unit in an inclined

position. It is designed to be operated in a
horizontal position only.

• Keep the unit and cassettes away from

equipment with strong magnets, such as
microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to

a warm location, moisture may condense
inside the VCR and cause damage to the
video head and tape. When you first install
the unit, or when you move it from a cold to
a warm location, wait for about four hours
before operating the unit.

Caution

Television programmes, films, video tapes and
other materials may be copyrighted.
Unauthorized recording of such material may
be contrary to the provisions of the copyright
laws. Also, use of this recorder with cable
television transmission may require
authorization from the cable television
transmitter and/or programme owner.

Compatible colour/TV systems

• This VCR is designed to record and play

back using the PAL (B/G, D/K and I),
MESECAM (B/G and D/K) and NTSC (M)
colour systems. Recording of video sources
based on other colour systems cannot be
guaranteed.

About colour systems

Different countries use different colour
systems and TV systems. These systems
handle such things as video playback and
recording differently. Using your VCR in a
country that is on a colour system not
supported by this VCR may cause problems
such as playback without sound, a vertically
rolling picture, etc.
This VCR is compatible with most of the
existing colour systems (NTSC, PAL, and
MESECAM) and TV systems (B/G, D/K, I,
and M) except for those used in France, Brazil,
Argentina, and Uruguay.

Содержание SLV-ED919MI













































































Отзывы: