Sony PCV-R532DS - Vaio Digital Studio Desktop Computer, Руководство по обслуживанию

Страница: 30 / 43

5-3
PCV-R532DS/R536DS/R538DS/R539DS
COM2 Optional header
8 pin standard 2mm single line header for COM2.
Connector location on MB See the frame harness diagram
Pin Signal Name
1 TxD2
2 Ground
3 RxD2
4 CTS2
5 5VSB
6 Ground
7 RI2#
8 RESERVED (N.C)
Front Panel I/O header
20 pin standard 2.5mm dual line header for LED/Switch unit
Connector location on MB See the frame harness diagram
pin assignments :
Pin Signal Name Pin Signal Name
1 PWR_BTN 11
2 PWR_BTN_G 12 MSG_LED-
3 IDELED- 13 KEYLOCK
4 14 KEYLOCK_G
5 KEY 15 SMI
6 P 16 SMI_G
7 PWR_LED- 17 +5V
8 P 18 NC
9 RESET 19 Ground
10 RESET G (GND) 20 SPKR
Battery Holder & Battery
Holder location on MB See the frame harness diagram
Battery vender Sony CR2032 or equivalent
Serial IRQ header
2 pin standard 2mm single line header for Serial IRQ signal
Connector location on MB See the frame harness diagram
Connector location on MB See the frame harness diagram
Pin assignments :
Pin Signal Name
1 IRQSER
2 Ground
IRQSER signal connect to the PCI4 connector via 0 ohm resister. Pin# is the A11.
Thermal measurement header
This header is used for thermal measurement at evaluation stage. This connector does
not need at production board. This signal also routed to Super I/O for thermal
monitoring.
Pin assignments :
Pin Signal Name
1 THERMDP ( CPU B14 )
2 THERMDN ( CPU B15 )
3 Ground
GPIO Header
3 pin standard 2mm single line header for GPIO from Sound controller
3 pin standard 2mm single line header for CPU thermal measurement
Connector location on MB See the frame harness diagram
pin assignments :
Pin
Signal Name
1 CLK(SCL),GPIO[4]
2 DATA(SDA),GPIO[3]
3 Ground
Pin assignments :
SOFA Connector
Callisto has same SOFA Header, the signal configuration for Europa is upper
compatible.
EMI filter consideration on Power lines.
pin assingments
Pin Signal Name Pin Signal Name
1 GND 2 GND
3 GND 4 GND
5 GND 6 GND
7 SYS_ON 8 PWRBTN#
9 GND 10 GND
11 +5VSB(EMI Filtered) 12 +5VSB(EMI Filtered)
13 TXD2 14 RXD2
15 +5V(EMI Filtered) 16 +5V(EMI Filtered)
17 CTS2 18 NC
19 +12V(EMI filtered) 20 +12V(EMI Filtered)
21 CLK(SCL),GPIO[4] 22 DATA(SDA),GPIO[3]
23 GND 24 GND
25 GND 26 GND
(note) PWRBTN# : control M/B power on/off.
SYS_ON : control M/B reset signal and secondary IDE reset signal.
GPIO[3,4] : CLK/DATA(I2C) control from 8810 Sound chip,shared with
GPIO header
TxD2,RxD2,CTS2 : shared with COM2 Optional header
1-2 External Connector
Parallel
Connector location on MB Rear side, see the frame harness diagram
:
Pin Signal Name Pin Signal Name
1 Strobe# 14 Auto Feed#
2 Data bit 0 15 Fault#
3 Data bit 1 16 INIT#
4 Data bit 2 17 SLCT IN#
5 Data bit 3 18 Ground
6 Data bit 4 19 Ground
7 Data bit 5 20 Ground
8 Data bit 6 21 Ground
9 Data bit 7 22 Ground
10 ACK# 23 Ground
11 Busy 24 Ground
12 Error 25 Ground
13 Select
Serial (COM1) Port
Connector location on MB Rear side, see the frame harness diagram
pin assignments :
Pin Signal Name
1 DCD
2 Serial In #
3 Serial Out #
4 DTR#
5 Ground
6 DSR
7 RTS
8 CTS
9 RI1#
pin assignments