Sony MDS-JA20ES - Minidisc Deck, Руководство по обслуживанию

Страница: 4 / 88

– 4 –
SECTION 1
SERVICING NOTES
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
MODEL IDENTIFICATION
— BACK PANEL —
TABLE OF CONTENTS
SELF-DIAGNOSIS FUNCTION
........................... 2
1. SERVICING NOTES
............................................... 4
2. GENERAL
................................................................... 12
3. DISASSEMBLY
......................................................... 15
4. TEST MODE
.............................................................. 21
5. ELECTRICAL ADJUSTMENTS
......................... 26
6. DIAGRAMS
6-1. Block Diagram – MD SERVO Section – ...................... 35
6-2. Block Diagram – MAIN Section – ................................ 37
6-3. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 40
6-4. Printed Wiring Board – BD Section – ........................... 41
6-5. Schematic Diagram – BD Section (1/2) – ..................... 43
6-6. Schematic Diagram – BD Section (2/2)– ...................... 45
6-7. Printed Wiring Boards
– BD SWITCH Section – ................................................ 47
6-8. Schematic Diagram
– BD SWITCH Section – ................................................ 48
6-9. Printed Wiring Board
– AUDIO Board (Component Side) – ............................ 49
6-10. Printed Wiring Boards
– AUDIO Board (Conductor Side),
RELEASE Board – ......................................................... 51
6-11. Schematic Diagram – AUDIO Section (1/2) – .............. 53
6-12. Schematic Diagram – AUDIO Section (2/2) – .............. 55
6-13. Printed Wiring Board – DIGITAL Section – ................. 57
6-14. Schematic Diagram – DIGITAL Section – .................... 59
6-15. Printed Wiring Boards – PANEL Section – .................. 61
6-16. Schematic Diagram – PANEL Section – ....................... 63
6-17. Printed Wiring Board
– POWER Board (Component Side) – ........................... 65
6-18. Printed Wiring Boards
– POWER Board (Conductor Side), AC Board – ........... 67
6-19. Schematic Diagram – POWER Section – ..................... 69
6-20. IC Pin Function Description ........................................... 78
7. EXPLODED VIEWS
................................................ 87
8. ELECTRICAL PARTS LIST
............................... 93
Part No.
4-998-731-1 π : AEP and UK models
4-998-731-2
π
: US model
4-998-731-3 π : Canadian model