manualshive.com logo in svg

Sony MCC3000MT, Инструкция по эксплуатации

Поделиться
Скачать
Sony MCC3000MT Скачать руководство пользователя страница 18

Removing the Connector Covers

18

P

repa

ra

ti

ons

When the unit is shipped from the factory, 
connector covers are attached to the HD SDI 
OUT A, B connectors VIDEO OUT connector, 
and EXT SYNC IN connector. To use one of 
these connectors, remove the cover as follows.

1

Remove the screw of the connector 
cover, using a screwdriver that matches 
the grooves of the screw.

2

Remove the connector cover.

Note

• Make sure the DC power cable is disconnected 

before performing the above.

• Save the screws and cover, so that you can 

reattach the cover if necessary.

Caution

These connectors are designed to allow direct 
contact with conductive circuits. Weak voltage 
may be present because of a failure in this unit. To 
prevent patients from touching these connectors 
accidentally, attach the connector covers when 
the connectors are not being used to connect to 
other devices.

Removing the Connector 
Covers

Содержание MCC3000MT

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды