— 16 —
KV-40XBR700
6. Adjust SUB (right) side color according to Service Mode for SHUE.
NO. Name
Control Function
03 SCOL
SUB COLOR
04 SHUE
SUB HUE
2103-2
VB4
VB3
VB2
VB1
COLOR: VB1 < VB4 (=VB1 + 0~90 mV)
HUE: VB2 < VB3 (=VB2 + 0~90 mV)
(HUE: Adjust data -2 STEP)
7. Write data into memory.
2-7. WHITE BALANCE (CRT) AND SUB
BRIGHT ADJUSTMENT
Preparation
• Input an all white 480I (15.734 KHz) signal into the VIDEO 1 input
terminal to perform the White Balance (highlight, cut-off) adjustments.
The parameters to adjust are in the CXA2150P in Service Mode.
1. Set the following:
Picture:
Full Mode
Pro Mode
Color:
Center
2. Adjust White Balance in the Service Mode and set the following data:
NO. Name
Control Function
Avg. Data
05 RDRV
R-DRIVE
Fix: 46
06 GDRV
G-DRIVE
Adjust
07 BDRV
B-DRIVE
Adjust
08 RCUT
R-CUT OFF
Fix: 41
09 GCUT
G-CUT OFF
Adjust
10 BCUT
B-CUT OFF
Adjust
2150P-1
3. Adjust Sub Brightness: Input an all black signal (to IRE 7.5% set up)
480i (15.75 KHz) signal into the VIDEO 1 input terminal. Adjust the
following parameter of CXA2150P-1:
4. Check Initial Data (Important).
NO. Name
Control Function
Avg. Data
04 SBRT
SUB-BRIGHT
20
CXA2150P-1
NO. Name
Control Function
Avg. Data
00 SBOT
SUB-BRT OFFSET
7
12 SBOF
SUB-BRT OFFSET
63
2150P-1
5. Repeat Steps 2-4.
2-8. RASTER CENTER ADJUSTMENT
Preparation:
• Input a monoscope signal.
• Set to NTSC (DRC) mode.
1. Set to Service Mode and adjust as follows:
NO. Name
Control Function
Avg. Data
06 AGNG
AGING 1, AGING 2
2
NO. Name
Control Function
Avg. Data
02 HSIZ
Horiz Size
45
NO. Name
Control Function
Avg. Data
00 HBLK
Blanking Enable
0
CXA2150P-2
CXA2150D-2
CXA2150D-3
2. Reduce HSIZ to see sides of raster.
3. Adjust H-Center with CXA2150D-2 00.
4. Adjust to the best screen position with H-CENT and write data.
5. Restore aging, HSIZ and HBLK to original condition.
2-9. PICTURE DISTORTION ADJUSTMENTS
2-9.1. NTSC (DRC) FULL MODE
ADJUSTMENT
1. Face the picture tube in an east-west direction.
2. Complete V-PIN and V-CEN adjsuments fi rst (A2150-D1 05 V-PIN,
A2150-D1 04 V-CEN).
3. Input a monoscope and crosshatch signal. Adjust the picture
distortion with the following service parameters to balance the best
condition for these two signals.
A2150-D1
00
VPOS
A2150-D1
01
VSIZ
A2150-D1
02
VLIN
A2150-D1
03
VSCO
A2150-D1
04
VCEN
A2150-D1
05
VPIN
A2150-D1
07
HTPZ
A2150-D2
01
HPOS
A2150-D2
02
HSIZ
A2150-D2
03
SLIN
A2150-D2
04
MPIN
A2150-D2
06
UCP
A2150-D2
07
LCP
A2150-D2
13
PPHA
A2150-D2
14
VANG
A2150-D2
15
LANG
A2150-D2
16
VBOW
A2150-D2
17
LBOW
Note
: Make sure that the picture size is within specs. Vertical size is
11.7 ± 0.1 sq. and horizontal size is 15.6 ± 0.1 sq.
4. Write data into memory and then set the screen to 1080i mode.