— 26 —
KV-27FV16/29FV16/29FV16C/32FS12/32FS16
5-4. MA BOARD ADJUSTMENTS
H. Frequency (Free Run) Check
1. Input a TV mode (RF) with no signal.
2. Connect a frequency counter to base of Q501
(TP-500 H. DRIVE) on the A Board.
3. Check H. Frequency for 15735 ± 200 Hz
V. Frequency (Free Run) Check
1. Select video 1 with no signal input.
2. Set the conditions for a standard setting.
3. Connect the frequency counter to TP-508 (V OUT) or
CN501pin
(V DY+) and ground on the A Board .
4. Check that V. Frequency shows 60 ± 4 Hz.
Drive (RDRV)
1. Input a color-bar signal and set the level to 75%.
2. In Standard mode, set PICTURE to maximum and COLOR
to minimum.
3. Activate the Service Adjustment Mode.
4. Set both GON and BON items. Using
and
; set each to
the following values. Leave RON set to “1”.
SERVICE RON 1
1: ON
0: OFF
R ON:
ON
(1)
G ON:
OFF (0)
B ON:
OFF (0)
5. Connect an oscilloscope probe to CA Board, J701 Pin 12
(KR) (Red Out) .
6. Select RDRV with
and
.
7. Adjust the value of RDRV with
and
for
92.5 ± 3 VDC.
8. Reset GON and BON values to “1”.
R ON:
ON
(1)
G ON:
ON
(1)
B ON:
ON
(1)
9. Reset Picture and Color to normal values:
PICTURE:
MAX
COLOR:
CENTER
10. Press
then
to save into the memory.
Display Position Adjustment (DISP)
1. Input a color-bar signal.
2. Set to Service Adjustment Mode.
3. Select DISP with
and
.
4. Adjust values of DISP with
and
to adjust characters
to the center.
5. Write to memory by pressing
then
.
6. Check to see if the text is displayed on the screen.
SERVICE DISP 15
Sub Bright Adjustment (SBRT)
1. Input a monoscope signal.
2. Activate the Service Adjustment Mode.
3. Set the PICTURE and BRIGHTNESS to minimum.
4. Select the SBRT item with
and
.
5. Adjust the values of SBRT with
and
to obtain a faintly
visible crosshatch.
6. Press
then
to save into the memory.
Sub Hue, Sub Color Adjustment (CHUE, CCOL)
1. Input a color-bar signal and set level to 75%.
2. Activate the Service Adjustment Mode.
3. Connect an oscilloscope probe to CA Board, CN705
Pin
.
4. Select the CHUE and CCOL item with
and
.
5. While showing the CHUE item, adjust the waveform with
and
until the second and third bars show the same level
(V2 = V3 < 0.1 Vp-p).
6. While showing the CCOL item, adjust the waveform with
and
until the first and fourth bars show the same level
(V1 = V4 < 0.1 Vp-p).
V1
V2 V3 V4
7. Press
then
to save into the memory.
V. Size Adjustment (VSIZ)
1. Input a crosshatch signal.
2. Activate the Service Adjustment Mode.
3. Select the VSIZ item with
and
.
4. Adjust value of VPOS with
and
for the best vertical
center.
5. Press
then
to save into the memory.
Содержание KV-32FS16 - 32" Trinitron Wega
Страница 28: ... 28 KV 27FV16 29FV16 29FV16C 32FS12 32FS16 NOTES ...
Страница 29: ... 29 KV 27FV16 29FV16 29FV16C 32FS12 32FS16 NOTES ...
Страница 30: ... 30 KV 27FV16 29FV16 29FV16C 32FS12 32FS16 NOTES ...
Страница 73: ... 91 KV 27FV16 29FV16 29FV16C 32FS12 32FS16 ...
