Sony KDP-57XBR2 - Digital High Definition Projection Tv, Руководство по обслуживанию

Страница: 225 / 228

22
Error code screen display when auto-
focus performed in service mode. Stored-error code screen displayed in
category “PJE”, item “ERR” (refer to
table above).
3-4. Auto Registration Error Code List
If an error code is displayed after the set has been fully adjusted correctly, please check the following items:
position, tilt, and sizing. If either of these adjustments are off, even slightly, the auto registration patterns
might not hit the four sensors properly (this occurs when the internal generator patterns are being flashed on
the screen for the sensor to read). Therefore, auto registration (also called auto convergence or auto focus)
cannot operate properly, causing an error code to be displayed. In order for this function to operate
properly, correct position, tilt, and size must be adjusted properly.
Error
Code
DESCRIPTION RECOMMENDATIONS
00 No Error
10 Sensor 0 low output Check sensor 0, connection/ wiring, circuit, and pattern position (Are patterns hitting
sensor ?) Adjust “64 VUP” if necessary.
11 Sensor 1 low output Check sensor 1, connection/ wiring, circuit, and pattern position (Are patterns hitting
sensor ?) Adjust “69 HLE” if necessary.
12 Sensor 2 low output Check sensor 2, connection/ wiring, circuit, and pattern position (Are patterns hitting
sensor ?) Adjust “73 HRIV” if necessary.
13 Sensor 3 low output Check sensor 3, connection/ wiring, circuit, and pattern position (Are patterns hitting
sensor ?) Adjust “68 VLOW” if necessary.
20 Sensor 0 high output Check sensor 0 and circuit.
21 Sensor 1 high output Check sensor 1 and circuit.
22 Sensor 2 high output Check sensor 2 and circuit.
23 Sensor 3 high output Check sensor 3 and circuit.
30 V CENT or SKEW
adjustment loop overflow Check “66 VMID” data and check registration condition.
31 H CENT or SKEW
adjustment loop overflow Check “71 HMID” data and check registration condition.
32 H LIN or SIZE adjustment
loop overflow Check “69 HLE” and "73 HRIV" data and check registration condition.
40 V CENT regi data overflow Check “66 VMID” data and confirm V CENT data (all mode) is not near +511.
41 H CENT regi data overflow Check “71 HMID” data and confirm H CENT data (all mode) is not near +511.
42 V SKEW regi data overflow Check “66 VMID” data and confirm V SKEW data (all mode) is not near +511.
43 H SKEW regi data overflow Check “71 HMID” data and confirm H SKEW data (all mode) is not near +511
44 H LIN regi data overflow Check “69 HLE” and “73 HRIV” data and confirm H CENT data (all mode) is not near +511.
45 H SIZE regi data overflow Check “69 HLE” and “73 HRIV” data and confirm V CENT data (all mode) is not near +511.
50 V CENT regi data overflow Check “66 VMID” data and confirm V CENT data (all mode) is not near –512.
51 H CENT regi data overflow Check “71 HMID” data and confirm H CENT data (all mode) is not near –512.
52 V SKEW regi data overflow Check “66 VMID” data and confirm V SKEW data (all mode) is not near –512.
53 H SKEW regi data overflow Check “71 HMID” data and confirm H SKEW data (all mode) is not near –512
54 H LIN regi data overflow Check “69 HLE” and “73 HRIV” data and confirm H CENT data (all mode) is not near –512.
55 H SIZE regi data overflow Check “69 HLE” and “73 HRIV” data and confirm V CENT data (all mode) is not near –512.
60 H or V CENT offset
overflow Check “71 HMID” data and check “66 VMID” data
61 H or V SKEW offset
overflow Check SKEW adjustment.
62 H SIZE or LIN offset
overflow Check “69 HLE” and “73 HRIV” data and check SIZE and LIN adjustment.
70 H or V CENT offset
overflow Check “71 HMID” data and check “66 VMID” data
71 H or V SKEW offset
overflow Check SKEW adjustment.
72 H SIZE or LIN offset
overflow Check “69 HLE” and “73 HRIV” data and check SIZE and LIN adjustment.
80 Size limit error Check that H SIZE data is a negative value and not near 0.