background image

HT-CT180

16

SECTION  3

TEST  MODE

VERSION  DISPLAY

The check of the software version can be performed.

Procedure:

1.  Press the [

@

/

1

] button to turn the power on.

2.  Press three buttons of the [INPUT], [VOL+] and [VOL

] si-

multaneously for 2 seconds.

3.  When enter the version display mode, the software version is 

shown by the frequency of blinking of each LED.

Software version

X.XX

Minor version (Lower) (BLUETOOTH function LED)

LED showing the software version

Minor version (Upper) (ANALOG function LED)

Major version  (OPTICAL function LED)

 

Example: When the software version is “1.02”

 

OPTICAL function LED is blink once.

 

ANALOG function LED is not blink.

 

BLUETOOTH function LED is blink twice.

4.  When the version display is 

fi

 nished, return to the normal 

mode.

FACTORY  RESET

It can clear all settings and the Bluetooth pairing history to initial 
conditions. Execute this mode when returning this unit to the cus-
tomer.

Procedure:

1.  Press the [

@

/

1

] button to turn the power on.

2.  Press three buttons of the [INPUT], [VOL

] and [

@

/

1

] simulta-

neously for 5 seconds.

3.  Blink three times all LEDs, then lights up all LEDs. When the 

reset is complete, all LEDs light off and becomes the standby 
status.

DEMO  MODE

The demo mode can be performed.
(This mode is used by shop front)

Procedure:

1.  Press the [

@

/

1

] button to turn the power on.

2.  Press two buttons of the [INPUT] and [VOL

] simultaneously 

for 5 seconds.

3.  When enter the demo mode, ANALOG function LED is blink 

twice quickly, then changed to the setting of initial value for 
demo mode.

blink twice quickly

Initial value for demo mode:

Function  

: OPTICAL

Volume  

25

Muting  

OFF

Sound 

fi

 eld 

: CLEAR AUDIO+

Night mode 

: OFF

Voice  

OFF

Subwoofer volume  : 10
Dual mono 

: MAIN

Note 1:

 When demo mode is “ON”, the operation of the [

@

/

1

] button on 

the unit, and the operation of the [

@

/

1

] and [INPUT] buttons on 

the remote commander is invalid.

Note 2:

 When the non-operation and no sound for 

fi

 ve minutes is fol-

lowed, setting will return to the initial value for demo mode.

Releasing method:

Perform the “FACTORY RESET”.

Note:

 The demo mode does not release by unplug the AC cord.

Содержание HT-CT180





































Отзывы: