Sony HCD-SBT100, Руководство по обслуживанию

Страница: 4 / 88

HCD-SBT100/SBT100B/SBT300W/SBT300WB
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(
Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The
fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc re
fl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTE OF REPLACING THE TUNER BOARD
When the TUNER board is defective, exchange the complete
mounted board.
NOTE OF REPLACING THE DAB BOARD
When the DAB board is defective, exchange the complete mount-
ed board.
NOTE OF REPLACING THE MS-476 BOARD
When the MS-476 board is defective, exchange the CDM90 ASSY
(Ref. No. CDM1).
NOTE OF REPLACING THE IC501, IC502, IC504, IC702,
IC841, IC851, IC902, IC903 AND IC904 ON THE MAIN
BOARD
IC501, IC502, IC504, IC702, IC841, IC851, IC902, IC903 and
IC904 on the MAIN board cannot exchange with single. When
these parts are damaged, exchange the complete mounted board.
NOTE OF REPLACING THE IC5003 ON THE NET BOARD
IC5003 on the NET board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
NOTE OF REPLACING THE IC5008 ON THE USB BOARD
IC5008 on the USB board cannot exchange with single. When this
part is damaged, exchange the complete mounted board.
CHECKING THE OPERATION AFTER REPAIR
After repair completion, connect the “iPod” etc. corresponding to
this unit, and check the operation of playback (HCD-SBT300W/
SBT300WB only), charge, etc.
NOTE OF PERFORMING THE OPERATION CHECK IN
THE STATE THAT HEAT SINK WAS REMOVED
When performing the operation check in the state that this unit was
disassembled, it is possible to perform the operation check in the
state that heat sink was removed. But perform the operation check
in the volume state as low as possible.
TEST DISCS
Use following TEST DISC (for CD) when this unit con fi rms the
operation and checks it.
Part No. Description
3-702-101-01 DISC (YEDS-18), TEST
4-225-203-01 DISC (PATD-012), TEST
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of sample disc in the
shop is equipped.
Releasing Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to turn the CD function.
3. Press two buttons of the [
x
] and [
Z
] simultaneously for fi ve
seconds.
4. The message “UNLOCKED” is displayed on the fl uorescent
indicator tube and the disc tray is unlocked.
Note: When “LOCKED” is displayed, the disc tray lock is not released by
turning power on/off with the [
?/1
] button.
MODEL IDENTIFICATION
Distinguish by Part No. on the rear side of a main unit.
– Rear Panel –
PART No.
Model Part No.
HCD-SBT100: AEP model 4-462-108-0
[]
HCD-SBT100: US model 4-462-108-1
[]
HCD-SBT100: Canadian model 4-462-108-2
[]
HCD-SBT100: Australian model
4-462-108-3
[]
HCD-SBT100B: AEP and UK models 4-462-108-7
[]
HCD-SBT300W: AEP model 4-463-724-0
[]
HCD-SBT300W: Australian model 4-463-724-1
[]
HCD-SBT300WB: AEP and UK models 4-463-724-2
[]
HCD-SBT300WB: Australian model 4-463-724-4
[]