![background image](http://html.mh-extra.com/html/sony/hcd-md515-component-for-dhcmd515/hcd-md515-component-for-dhcmd515_service-manual_420815022.webp)
– 22 –
4-8. OPERATING THE CONTINUOUS RECORDING
MODE
4-8-1.
Entering the Continuous Recording Mode
1. Set the MO disc in the slot 1 of unit. (Refer to note 3.)
2. Turn the MULTI JOG dial and display “CREC MODE”.
3. Press the ENTER/YES button to change the display to “CREC
MID”.
4. When access completes, the display changes to “CREC
(
)” and
REC
lights up.
Note: The numbers “ ” displayed shows you the recording position ad-
dress.
4-8-2.
Changing the Parts to be Recorded
1. When the ENTER/YES button is pressed during continuous
recording, the display changes as below. (“PROGRAM”
indication turns off during change-over of display.)
4-7. OPERATING THE CONTINUOUS PLAYBACK
MODE
4-7-1.
Entering the Continuous Playback Mode
1. Set the disc in the slot 1 of unit. (In several seconds it will be
automatically pulled in.) (Whichever recordable discs or discs
for playback only are available.)
2. Turn the MULTI JOG dial and display “CPLAY MODE”.
3. Press the ENTER/YES button to change the display to “CPLAY
MID”.
4. When access completes, the display changes to
“C =
AD=
)”.
Note: The numbers “ ” displayed show you error rates and ADER.
4-7-2.
Changing the Parts to be Played-back
1. Press the ENTER/YES button during continuous playback to
change the display as below.
2. When access completes, the display changes to
“C1=
AD=
”.
Note: The numbers “ ” displayed show you error rates and ADER.
4-7-3.
Ending the Continuous Playback Mode
1. Press the EDIT/NO button. The display will change to
“CPLAY MODE”.
2. Press the MD
6
button and remove the disc.
Notes:
1.
The playback start address for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID
: 300h cluster
OUT
: 700h cluster
In case you want to display the address of the playback position on the
display, press the DISPLAY button and display “CPLAY (
)”.
2.
The EDIT/NO button can be used to stop playing anytime.
2. When access completes, the display changes to “CREC
(
)” and
REC
lights up.
Note: The numbers “ ” displayed shows you the recording position ad-
dress.
4-8-3.
Ending the Continuous Recording Mode
1. Press the EDIT/NO button. The display will change to “CREC
MODE” and
REC
goes off.
2. Press the MD
6
button and remove the disc.
Notes:
1.
The recording start address for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID
: 300h cluster
OUT
: 700h cluster
2.
The EDIT/NO button can be used to stop recording anytime.
3.
During the test mode, the erasing-protection tab will not be detected.
Therefore be careful not to set the continuous recording mode when a
disc not to be erased is set in the unit.
4.
Do not perform continuous recording for long periods of time above 5
minutes.
5.
During continuous recording, be careful not to apply vibration.
4-9. EEP MODE
This mode reads and writes the contents of the non-volatile
memory.
It is not used in servicing. If set accidentally, press the
EDIT/NO button immediately to exit it.
CPLAY MID
CPLAY OUT
CPLAY IN
CREC MID
CREC OUT
CREC IN
Содержание HCD-MD515 - Component For Dhcmd515
