Sony HCD-BC150 - Dvd Home Theater System, Руководство по обслуживанию

Страница: 90 / 218

6
HCD-BC150/BC250
FZC Count : The number of times which focus zero cross points
of each layer when lens down.
PI Reference : The average of PI reference voltage. (hexadecimal
number)
PI Peak : PI peak level voltage. It performs only when disc
type judgment is successful. (hexadecimal number)
2-1-2. Disc Type DVD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: DVD single layer disc (12 cm)
[2]
: DVD dual layer disc (0 layer, 12 cm)
[3]
: DVD dual layer disc (1 layer, 12 cm)
[4]
: DVD-RW disc (12 cm)
[5]
: DVD single layer disc (8 cm)
[6]
: DVD dual layer disc (0 layer, 8 cm)
[7] : DVD dual layer disc (1 layer, 8 cm)
[8]
: DVD-RW disc (8 cm)
2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: CD disc (normal speed, 12 cm)
[2]
: CD disc (double speed, 12 cm)
[3]
: CD disc (normal speed, 8 cm)
[4]
: CD disc (double speed, 8 cm)
[5]
: CD-RW disc (normal speed, 12 cm)
[6]
: CD-RW disc (double speed, 12 cm)
[7]
: CD-RW disc (normal speed, 8 cm)
[8]
: CD-RW disc (double speed, 8 cm)
2-1-4. Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: SACD Hybrid disc (SACD layer, 12 cm)
[2]
: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]
: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4] : SACD Hybrid disc (SACD layer, 8 cm)
[5]
: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]
: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing this item.
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
Servo Control
1.LD off R.Sled FWD
2.Focus off L.Sled REV
3.SPDL off U.Sled Reset
4.CLVA off D.Sled Limit
5.Trk. off
6.Sled off
7.Fcs.Srch off
8.Fcs.OppL off
0.All Servo Off
Exit: RETURN
Note:
1. Set correctly the disc type to be used on the Disc
Type screen.
2.
In case of an alarm, immediately press the
x
stick
to stop the servo operation, and press the
+/1
button to turn the power off.
Basic operation:
(controllable from front panel or remote commander)
+/1
: Power OFF (release the Test Mode)
x
: Servo stop
A (DISC1) : Stop and eject/Loading
RETURN
O
“R” : Return to Operation Menu or Test
Mode Menu
.
“R” ,
>
“ R” : Transition between sub modes of
menu
1 “R” to 9 “R” , 0 “R” : Selection of menu items
Cursor
v
“R” /
V
“R” : Increase/Decrease in manually
adjusted value
2-1. Disc Type
2-1-1. Disc Type Auto Check
1) Press the 1 “R” key on the remote commander to display the
Disc Type Auto Check screen.
2) Insert a disc and press the ENTER/YES “R” key on the remote
commander.
3) It judges the type of inserted disc automatically and displays
the disc type and so on as below.
Disc Type : CD, DVD or Hybrid (SACD)
Layer : SINGLE, DUAL or HYBRID
Mirr Time : Mirror time of between disc surface and record
surface when disc type judgment. (hexadecimal
number)
Mirr Count : The number of times which mirror counts between
disc surface and record surface when disc type
judging.
Disc Type
Disc Type Select
1. Disc Type Auto Check
2. Set Disc Type DVD
3. Set Disc Type CD
4. Set Disc Type Hybrid
Exit: RETURN
Disc Type Auto Check
Disc Type xx
Layer xx
Mirr Time xx
Mirr Count xx
FZC Count xx
PI Reference xx
PI Peak xx
ENTER.Execute
Exit: RETURN