6-1
6-3.
SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press
[0]
key on the remote com-
mander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1. All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
>
key to go to the next item,
or
.
key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press
x
or
[ENTER]
key.
If an error occurred, the diagnosis is suspended and the error code
is displayed as shown below.
### Syscon Diagnosis ###
3-3. EEPROM Check
Error 03: EEPROM Write/Read N
Address
: 00000001
Write Data
: 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press
x
key to quit the diagnosis, or
.
key to repeat the same
item where an error occurred, or
>
key to continue the check
from the item next to faulty item.
6-1.
GENERAL DESCRIPTION
The Test Mode allows you to make diagnosis and adjustment eas-
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
Note: Since the remote commander belongs to this model has no
number buttons, use other DVD remote commander with
number buttons on it.
6-2.
STARTING TEST MODE
Press the
[TOP MENU]
,
[CLEAR]
,
[I/ ]
keys on the remote com-
mander in this order with the power of main unit in OFF status,
and the Test Mode starts, and the menu shown below will be dis-
played on the TV screen. At the bottom of menu screen, the model
name and revision number are displayed. Last Off at the lower
right of screen indicates the information code concerning the last
power off.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the
[I/ ]
key.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. ------
4. Emargency Hisory
5. Version Information
6. Video Level Adjustment
Exit: Power Key
_
Model:DPX-17xxxx
Revision:x.xxx
Last Off: xx
Power Off Information Code List
00 :
Primary Power Off
01 :
Power Off Request from SYSTEM CONTROL
02 :
Power Off by Emergency Power Off Command from SYS-
TEM CONTROL
(if information is sent from SYSTEM CONTROL)
IF CON Judged that SYSTEM CONTROL is Faulty
Power Off from Diagnosis Mode of IF CON
Power Off by Power Supply Voltage Monitor
SECTION 6
TEST MODE
DVP-PQ2
1
1
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
