1-21
86
Settings for the Speakers
(SPEAKER SETUP)
To obtain the best possible surround sound,
set the size of the speakers you have
connected and their distance from your
listening position. Then use the test tone to
adjust the volume and the balance of the
speakers to the same level.
This setting is effective when connecting the
speaker with 5.1CH OUTPUT jacks (page
22).
Select
“
SPEAKER SETUP
”
in the setup
display. For details, see
“
Using the Setup
Display
”
(page 77).
The default settings are underlined.
To return to the default setting
Select the item, then press CLEAR. Note that
only the SIZE setting does not return to the
default setting.
x
SIZE
Selects the size of the speakers to be
connected.
• FRONT
• CENTER
• REAR
* Rear speaker position
Correctly specify the location of the rear speakers to
enjoy the surround effect.
•
Set to the
“
SIDE,
”
if the location of the rear speakers
corresponds to section
A
below.
•
Set to the
“
REAR,
”
if the location of the rear
speakers corresponds to section
B
below.
This setting affects only
“
VIRTUAL REAR SHIFT,
”
“
VIRTUAL MULTI REAR,
”
and
“
VIRTUAL
MULTI DIMENSION
”
mode (page 58).
These settings do not affect the SACD Multi audio
signals.
LARGE
Normally select this position.
SMALL
When the sound cracks or the
surround sound effects are difficult to
hear, select this. This activates the
bass redirection circuitry and outputs
the bass frequencies of the front
speaker from the subwoofer.
NONE
If you do not connect a center
speaker, select this.
SPEAKER SETUP
DISTANCE:
BALANCE:
LEVEL:
OFF
TEST TONE:
FRONT:
CENTER:
YES
LARGE(REAR)
LARGE
LARGE
REAR:
SUBWOOFER:
SIZE:
LARGE
Normally select this position.
SMALL
When the sound cracks or the
surround sound effects are difficult to
hear, select this. This activates the
bass redirection circuitry and outputs
the bass frequencies of the center
speaker from other speakers.
NONE
If you do not connect rear speakers,
select this.
LARGE
(REAR/SIDE): Normally select this
position. Select either of these
according to the rear speaker
’
s
position*.
SMALL
(REAR/SIDE): When the sound
cracks or the surround sound effects
are difficult to hear, select this.
Select either of these according to the
rear speaker
’
s position*.
This activates the bass redirection
circuitry and outputs the bass
frequencies of the rear speaker from
other speakers.
90
20
45
87
Se
ttings
a
nd Adj
u
s
tm
e
n
ts
•
SUBWOOFER
Notes
•
The cut off frequency for the subwoofer is fixed at
120 Hz.
•
If your speakers are too small to reproduce low bass
frequencies, please set all speaker settings to
“
SMALL
”
and utilize a subwoofer for low
frequency sound.
•
Even if there are fewer than 6 speakers connected,
the player distributes the audio signal components to
the front speakers.
x
DISTANCE
In order to set the distance for each speaker,
first set the distance from the listening
position to the front speaker using FRONT.
This will automatically set the same distance
for the CENTER and REAR speakers. Then,
starting from these settings, change the
distance for the center and rear speakers as
explained below so that they match the actual
physical distance to your listening position.
The default distance setting for the speakers
in relation to the listening position is shown
below.
Be sure to change the value in the Setup
Display when you move the speakers. The
default adjustments are in parentheses.
Notes
•
If each of the front or rear speakers are not placed at
an equal distance from your listening position, set
the distance according to the closest speaker.
•
Do not place the rear speakers farther away from
your listening position than the front speakers.
•
These settings do not affect the SACD Multi audio
signals.
NONE
If you do not connect a subwoofer,
select this. This activates the bass
redirection circuitry and outputs the
LFE signals from the front speakers as
long as the front speaker size is set to
“
LARGE.
”
YES
If you connect a subwoofer, select this
to output the LFE (low frequency
effect) channel from the subwoofer.
When you set the other speakers
settings to
“
SMALL,
”
the subwoofer
makes up for the missing bass
frequencies of the speakers.
FRONT
(10ft/3m)
Front speaker distance from the
listening position can be set in 1
foot (0.3 meter) increments from
4 to 50 feet (1.2 to 15.2 meters).
CENTER
(10ft/3m)
Center speaker distance can be
moved up to 2 feet (0.6 meters)
backward from the front
speakers or 5 feet (1.5 meters)
forward closer to the listening
position, in 1 foot (0.3 meter)
increments.
REAR (10ft/
3m)
Rear speaker distance can be
moved up to 16 feet (4.8 meters)
closer to your listening position
from the front speaker position,
in 1 foot (0.3 meter) increments.
10ft/3m
10ft/3m
10ft/3m
10ft/3m
10ft/3m
continued
,
88
x
BALANCE
You can vary the balance of the left and right
speakers as follows. Be sure to set
“
TEST
TONE
”
to
“
ON
”
for easy adjustment.
The default adjustments are in parentheses.
x
LEVEL
You can vary the level of each speaker as
follows. Be sure to set
“
TEST TONE
”
to
“
ON
”
for easy adjustment.
The default adjustments are in parentheses.
To adjust the volume of all the
speakers at one time
Use the amplifier
’
s (receiver
’
s) volume
control.
x
TEST TONE
The speakers will emit a test tone. Use this
when you use the 5.1CH OUTPUT jacks and
adjust the
“
BALANCE
”
and
“
LEVEL.
”
Adjusting the speaker volume and
level
1
Select “SPEAKER SETUP” in the Setup
Display.
2
Select “TEST TONE” and set to “ON.”
You will hear the test tone from each
speaker in sequence.
3
From your listening position, select
“BALANCE” or “LEVEL” and adjust the
value of “BALANCE” using
C
/
c
and
“LEVEL” using
X
/
x
.
The test tone is emitted from both left and
right speakers simultaneously.
4
Select “TEST TONE” and set to “OFF” to
turn off the test tone.
Notes
•
When you adjust the speaker settings, the sound cuts
off for a moment.
•
The test tone signals are not output from the digital
jack.
FRONT
(0dB)
Adjust the balance between the
front left and right speakers (
–
6dB [L] to +6dB [R], 0.5dB
increments).
REAR (0dB)
Adjust the balance between the
rear left and right speakers (
–
6dB [L] to +6dB [R], 0.5dB
increments).
FRONT (0dB)
Adjust the level of the front
speakers (
–
6dB to 0dB, 0.5
dB increments).
CENTER
(0dB)
Adjust the level of the center
speaker (
–
12dB to 0dB,
0.5dB increments).
REAR (0dB)
Adjust the level of the rear
speakers (
–
12dB to 0dB,
0.5dB increments).
SUBWOOFER
(0dB)
Adjust the level of the
subwoofer (
–
10dB to +10dB,
0.5dB increments).
OFF
The test tone is not emitted from
the speakers.
ON
The test tone is emitted from
each speaker in sequence while
adjusting balance or level.
When you select one of the
“
SPEAKER SETUP
”
items, the
test tone is emitted from both left
and right speakers simultaneously.
89
Addit
io
na
l Information
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
,
Check that the AC power cord is connected
securely.
Picture
There is no picture.
,
The connecting cords are not connected
securely.
,
The connecting cords are damaged.
,
The player is not connected to the correct TV
input jack (page 18).
,
The video input on the TV is not set so that you
can view pictures on the player.
Picture noise appears.
,
The disc is dirty or flawed.
,
If the picture output from your player goes
through your VCR to get to your TV, the copy-
protection signal applied to some DVD
programs could affect picture quality. If you
still experience problems even when you
connect your player directly to your TV,
please try connecting your player to your TV
’
s
S video input (page 18).
Even though you set the aspect ratio
in
“
TV TYPE
”
of
“
SCREEN SETUP,
”
the picture does not fill the screen.
,
The aspect ratio of the disc is fixed on your
DVD.
Sound
There is no sound.
,
The connecting cord is not connected securely.
,
The connecting cord is damaged.
,
The player is connected to the wrong input
jack on the amplifier (receiver) (page 22, 24,
26).
,
The amplifier (receiver) input is not changed
so that you can listen to the player.
,
The player is in pause mode or in Slow-motion
Play mode.
,
The player is in fast forward or fast reverse
mode.
,
If the audio signal does not come through the
DIGITAL OUT (OPTICAL or COAXIAL)
jack, check the audio settings (page 83).
,
SACD audio signals are not output from a
digital jack.
Sound is noisy.
,
The disc is dirty or flawed.
Sound distortion occurs.
,
Set
“
AUDIO ATT
”
in
“
AUDIO SETUP
”
to
“
ON
”
(page 83).
The surround effect is difficult to hear
when you are playing a Dolby Digital,
or DTS sound track.
,
Check the speaker connections and setting
(page 22, 24, 26).
,
Depending on the DVD, the output signal may
not be the entire 5.1 channels. It may be
monaural or stereo even if the sound track is
recorded in Dolby Digital or DTS format.
The sound comes from the center
speaker only.
,
Depending on the disc, the sound may come
from the center speaker only.
,
Set
“
SURROUND
”
to
“
OFF
”
in the Control
Menu display (page 58).
continued
,
Содержание DVP-NC650V
Страница 1: ......
