Sony DVCAM DSR-PD150, Руководство по обслуживанию

Страница: 202 / 279

5-58
3-1-2. Precautions on Adjusting
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to “VCR” (or
“PLAYER”) or set the “Forced VTR Power ON mode” using
the adjustment remote commander (Note 1).
To set to the Camera mode, set the power switch to “CAMERA”
or set the “Forced Camera Power ON mode” using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note 3)
2) The handle block (XLR connector, Microphone amplifier,
remote commander receiver, VTR function key) need not be
connected except during “Battery End Adjustment” and “Audio
adjustments”. To remove, disconnect the following connector.
FK-076 board CN501 (36P, 0.8mm)
3) By setting the “Forced VTR Power ON mode” or “Forced
Camera Power ON mode”, the video section can be operate
even if the cabinet (L) (Control switch block (CF-4980)) has
been removed. When removing the cabinet (L) disconnect the
following connector.
VC-242D board CN009 (14P, 0.5mm)
4) Cabinet (R) (CK-093board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-242D board
CN008) means removing the lithium 3V power supply (CK-
093 board, BT250) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data. If
the cabinet (R) has been removed, the self-diagnosis data, data
on history of use (total drum rotation time etc.) will be lost.
Before removing, note down the self-diagnosis data and the
data on the history use (data of page: 2, address: A2 to AA).
(Refer to “SELF-DIAGNOSIS FUNCTION” for the self-
diagnosis data, and to “5-4.Service Mode” for the data on the
history use.)
To remove the cabinet (R), disconnect the following connector.
VC-242D board CN008 (50P, 0.5mm)
5) The viewfinder (LB-065 board) is need not be connected. To
remove it, disconnect the following connector.
VC-242D board CN8612 (27P, 0.3mm)
6) The FP-200 (flexible) is need not be connected. To remove it,
disconnect the following connectors.
VC-242D board CN004 (10P, 0.5mm)
LA-026 board CN053 (27P, 0.5mm)
7) The LA-026 board is need not be connected. To remove it,
disconnect the following connectors.
VC-242D board CN023 (80P, 0.5mm)
8) The CD-254 board of the lens block is need not be connected.
To remove it, disconnect the following connectors.
VC-242D board CN025 (50P, 0.5mm)
Note 1:
Setting the “Forced VTR Power ON” mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned on
with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 2: Setting the “Forced Camera Power ON” mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 3: Setting the “Forced Memory Power ON” mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the memory power to be turned
on with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 4:
Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
3-1-3. HOW TO ENTER RECORD MODE WITHOUT
CASSETTE
1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0C, and press the PAUSE
button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)
Note:
The function buttons become inoperable.
5) To quit the record mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the record mode, be
sure to quit following this procedure.)
3-1-4. HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE
1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0B, and press the PAUSE
button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)
Note:
The function buttons become inoperable.
5) To quit the playback mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the playback mode,
be sure to quit following this procedure.)