manualshive.com logo in svg

Sony DECR-1000 A, Инструкция по эксплуатации

Поделиться
Скачать
Sony DECR-1000 A Скачать руководство пользователя страница 9

G:\Sagyou\07 Jul\0706\837913S DECR-1000 
A_GB\2886333111DEHR1000\01GB04PRE.fm

masterpage:Right

DECR-1000 A

2-886-333-

11

(1)

9

Equipment required to configure the reference system

Equipment required to configure the reference system

The following items are required to use the evaluation software package provided by SCE.

DECR-1000 A (this unit)

See “Part names and usage” (

t

page 10).

Monitor

Either or both of the following can be used for graphics output from this unit:

•

Standard PC monitor 
Connected to the monitor connector of this unit

•

TV monitor (supporting 480i, 480p, 1080i, 720p or 1080p)
Connected to the HDMI OUT connector or AV MULTI OUT connector of this unit

Development host PC

Coding, compiling, and debugging should be performed on a separate development host PC, which may 
be a standard PC. When using a standard PC, it should be equipped with an Ethernet connector.

Refer to the “Reference Tool Software Setup Guide” document (supplied separately) for other 
recommended functions and a description of performance levels.

Configuring the reference system requires the following:

•

Installing the software package that comes with this unit on the development host PC. 
Refer to the “Reference Tool Software Setup Guide” document (supplied separately).

•

Setting up the reference tool. 
Refer to “Preparing to use this unit” (

t

page 16).

Equipment required to configure the reference 
system

Reference system setup

01GB01COV.book  Page 9  Thursday, July 6, 2006  2:50 PM

Содержание DECR-1000 A










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды