DSC-HX200/HX200V_L2
2-5
2-1-3. LENS SECTION
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
#155
When disassembly and re-assembly this
block, must open the flash.
#12
#155
#30
Cabinet (Front) section
(See page 2-8)
2
Cabinet (Upper) Section
(See page 2-6)
1
101
103
(Note 1)
104
(Note 3)
105
106
(including CP001
(CMOS imager))
(Note 2)
107
102
108
109
(Note 4)
3
(Claws)
(Note 4)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
1-856-156-11
OPTICAL UNIT (NY213B)
(Note 4)
102
4-284-296-01 SHEET,
PD
103
4-276-127-01
MASK (NY213B) (Note 1)
104
1-856-188-31
FILTER BLOCK, OPTICAL (Note 3)
105
4-258-931-01
RUBBER (NY213B), SEAL
106
A-1864-704-A CD-814 BOARD, COMPLETE
(including CP001 CMOS imager) (Note 2)
107
1-882-898-11
CN-470 FLEXIBLE BOARD
108
4-284-293-01
SHEET (LENS), RADIATION
109
4-284-294-01 GASKET
(CMOS)
(Note 4)
#12
3-080-204-21 SCREW,
TAPPING,
P2
#30
3-086-156-11 SCREW
B1.2
#155 3-080-204-31 SCREW,
TAPPING,
P2
Screw
Note
Note 1:
Refer to “Assembly-1: Installation Cautions of the Mask
(NY213B).”.
Note 1:
“Assembly-1: Installation Cautions of the Mask (NY213B).”
を参照してください。
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
3
Note 2:
Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 2:
イメージャの交換時はLevel 3の6-1ページ、 “イメージャ
交換時の注意” を必ずお読みください。
1
#155 X 4
→
Open Flash
#155
Back View
2
#12 X 2
#12
Back View
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3.5
1.2
1.7
6.0
#155: M1.7 X 6.0 (Tapping)
(Black)
3-080-204-31
Note 3:
Refer to “Assembly-7: How to distinguish the side of Optical
Filter Block facing to Lens Device.”.
Note 3:
“Assembly-7: How to distinguish the side of Optical Filter
Block facing to Lens Device.” を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05
Note 4:
When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
Note 4:
この部品を取り外したときは調整が必要です。
調整方法については Adjust manual の Noteタブにある
Adjustment items after replacing parts を参照してください。
