background image

2

GB

CMT-M70    4-239-398-

11

(3) GB

WARNING

To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.

Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.

This appliance is classified
as a  CLASS 1 LASER
product.  This label is
located on the rear exterior.

To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc.  And don’t place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.

Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.

NOTICE FOR THE CUSTOMERS IN THE
U.S.A.

This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.

This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.

CAUTION

The use of optical instruments with this product will
increase eye hazard.

Note to CATV system installer:

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.

WARNING

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.  These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.  This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.  However,
there is no guarantee that interference will not occur
in a particular installation.  If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is
connected.

– Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.

NOTICE FOR THE CUSTOMERS IN
CANADA

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE
THIS POLARIZED AC PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.

Except for the European model

E

NERGY 

S

TAR

®

 is a U.S.

registered mark.
As an 

E

NERGY 

S

TAR

®

 partner,

Sony Corporation has determined
that this product meets the

E

NERGY 

S

TAR

®

 guidelines for

energy efficiency.

Содержание CMT-M70 Primary

























Отзывы: